Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
MODELS 7803R AND 7803R–EU HEAVY–DUTY
Models 7803R and 7803R–EU Reversible Drills are designed for drilling, honing,
reaming and hole sawing.
Ingersoll–Rand is not responsible for customer modification of tools for applications
on which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
•
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
•
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8" (10 mm) inside diameter air supply
hose.
•
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
•
Do not use damaged, frayed or deteriorated air
hoses and fittings.
•
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
•
Always use clean, dry air at 90 psig
(6.2 bar/620 kPa) maximum air pressure. Dust,
corrosive fumes and/or excessive moisture can ruin
the motor of an air tool.
•
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
•
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
Ingersoll–Rand Company 2000
Printed in U.S.A.
All manuals and user guides at all-guides.com
INSTRUCTIONS FOR
REVERSIBLE AIR DRILLS
TPD1459
03536976
USING THE TOOL
•
Always wear eye protection when operating or
performing maintenance on this tool.
•
Always wear hearing protection when operating
this tool.
•
Keep hands, loose clothing and long hair away
from rotating end of tool.
•
Note the position of the reversing lever before
operating the tool so as to be aware of the direction
of rotation when operating the throttle.
•
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
•
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
•
Tool accessory may continue to rotate briefly after
throttle is released.
•
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
•
Use accessories recommended by Ingersoll–Rand.
•
This tool is not designed for working in explosive
atmospheres.
•
This tool is not insulated against electric shock.
Form P6899
GB
Edition 6
May, 2000
Publicidad
Manuales relacionados para Ingersoll Rand 7803R
Resumen de contenidos para Ingersoll Rand 7803R
- Página 1 MODELS 7803R AND 7803R–EU HEAVY–DUTY REVERSIBLE AIR DRILLS TPD1459 Models 7803R and 7803R–EU Reversible Drills are designed for drilling, honing, reaming and hole sawing. Ingersoll–Rand is not responsible for customer modification of tools for applications on which Ingersoll–Rand was not consulted.
-
Página 2: Placing Tool In Service
Free Speed Chuck Capacity dB (A) Level •Power in (mm) Pressure 7803R, 7803R–EU reversible, pistol 1/2 (13) 92.9 105.9 Tested in accordance with ANSI S5.1–1971 at free speed ♦ Tested in accordance to ISO8662–1 at 80% rated free speed •... -
Página 3: Declaration Of Conformity
Ingersoll–Rand, Co. (supplier’s name) Swan Lane, Hindley Green, Wigan WN2 4EZ (address) declare under our sole responsibility that the product, Model 7803R–EU Reversible Air Drills to which this declaration relates, is in compliance with the provisions of 98/37/EC Directives. EN292 ISO8662 By using the following Principle Standards: (1994 →... -
Página 4: Utilisation De L'OUtil
PERFORMANCE MODÈLES 7803R ET 7803R–EU TPD1459 NOTE Les perçeuses réversibles Modèles 7803R et 7803R–EU sont destinées aux opérations de perçage, de rodage, d’alésage et de sciage de trou. Ingersoll–Rand ne peut être tenu responsable de la modification des outils par le client pour les adapter à... -
Página 5: Mise En Service De L'OUtil
Vitesse libre Capacité du mandrin dB (A) vibration •Puissance tr/mn pouces (mm) Pression 7803R, pistolet, réversible 1/2 (13) 92,9 105,9 7803R–EU Testé conformément à ANSI S5.1–1971 en vitesse libre ♦ Testé conformément à ISO8662–1 a 80% vitesse libre nominale •... -
Página 6: Certificat De Conformité
(nom du fournisseur Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse déclarons sous notre seule responsabilité que le produit: Perçeuses Pneumatiques Réversibles Modèle 7803R–EU objet de ce certificat, est conforme aux prescriptions des Directives: 98/37/CE EN292 ISO8662 en observant les normes de principe suivantes: (1994 →... - Página 7 UMSTEUERBARE HOCHLEISTUNGS–BOHRMASCHINEN DER BAUREIHE 7803R UND 7803R–EU HINWEIS Umsteuerbare Bohrmaschinen der Baureihe 7803R und 7803R–EU werden eingesetzt zum Bohren, Honen, Räumen und Lochsägen. Ingersoll–Rand lehnt jede Haftung für Veränderungen an Werkzeugen ab, die ohne vorherige Rücksprache mit Ingersoll–Rand vorgenommen werden.
-
Página 8: Technische Daten
Griffart Freie Spannfutter– Drehzahl kapazität dB (A) gungs– intensität •Leistung U/min Zoll (mm) Druck 7803R, 7803R–EU umsteuerbar, 1/2 (13) 92,9 105,9 Pistolengriff Gemäß ANSI S5.1–1971 bei freier Drehzahl getestet ♦ Gemäß ISO8662–1 bei 80% der freien Nenndrehzahl getestet • ISO3744... -
Página 9: Konformitätserklärung
(Name des Herstellers) Swan Lane, Hindley Green, Wigan WN2 4EZ (Adresse) erklären hiermit, gemäß unserer alleinigen Verantwortung, daß die Geräte: Umsteuerbare Hochleistungs–Bohrmaschinender Baureihe 7803R–EU auf die sich diese Erklärung bezieht, den Richtlinien: 98/37/EG unter Anlehnung an die folgenden Grundnormen EN292 ISO8662 entsprechen: (1994 →... - Página 10 I MODELLI DI TRAPANI PNEUMATICI REVERSIBILE 7803R E 7803R–EU HEAVY DUTY AVVISO I trapani reversibile modelli 7803R e 7803R–EU sono stati progettati per la trapanatura, smerigliatura. alesatura e segatura a tazza. La Ingersoll–Rand non è responsabile delle modifiche apportate alle pompe dai clienti per adattarli ad applicazioni per le quali la Ingersoll–Rand non sia stata interpellata.
- Página 11 (A) vibrazione •Potenza giri/min poll. (mm) Pressione 7803R, 7803R–EU reversibile 1/2 (13) 92,9 105,9 immissione a leva Collaudato secondo i criteri ANSI S5.1–1971 a velocità libera ♦ Collaudato secondo i criteri ISO8662–1 a velocità libera nominale dell’80% •...
-
Página 12: Dichiarazione Di Conformità
(nome del fornitore) Swan Lane, Hindley Green, Wigan WN2 4EZ (indirizzo) dichiariamo sotto la nostra unica responsabilità che il prodotto: Trapani pneumatici reversibile modell 7803R–EU a cui si riferisce la presente dichiarazione è conforme alle normative delle direttive: 98/37/CE EN292 ISO8662 secondo i seguenti standard: (1994 →... -
Página 13: Uso De Herramienta
MODELOS 7803R Y 7803R–EU TPD1459 NOTA Los Taladros Reversibles Modelos 7803R y 7803R–EU están diseñados para taladrado, rectificación, rebordeado y serrado de agujeros. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand. -
Página 14: Etiquetas De Aviso
TUBERÍAS PRINCIPALES 3 VECES EL TAMAÑO DE ENTRADA DE HERRAMIENTA NEUMÁTICA AL SISTEMA NEUMÁTICO Ingersoll–Rand N_. 50 Ingersoll Rand N_. 28 A LA Utilice siempre un lubricante de aire comprimido con esta HERRA– herramienta. Recomendamos la siguiente unidad de MIENTA NEUMÁTICA Filtro–Lubricador–Regulador:... -
Página 15: Declaracion De Conformidad
(nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Taladros Neúmaticos Reversibles Modelo 7803R–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE EN292 ISO8662 conforme a los siguientes estándares:... -
Página 16: Gebruik Van Het Gereedschap
TYPEN 7803R EN 7803R–EU OMKEERBARE BOORMACHINES VOOR ZWAAR WERK LET WEL De Typen 7803R en 7803R–EU Omkeerbare Boormachines zijn bedoeld voor het boren, honen, ruimen en gatzagen. Ingersoll–Rand is niet aansprakelijk voor door de klant aangebrachte veranderingen aan de gereedschappen voor toepassingen waarover met Ingersoll–Rand geen voorafgaand overleg werd gepleegd. -
Página 17: Specificaties
Type Soort Hendel Onbelast Capaciteit toerental Houder dB (A) niveau •Vermogen in (mm) Deuk 7803R, 7803R–EU omkeerbare pistool 1/2 (13) 92,9 105,9 Getest volgens ANSI S5.1–1971 bij vrije snelheid ♦ Getest volgens ISO8662–1 bij 80% nominale vrije snelheid • ISO3744... - Página 18 Ingersoll–Rand, Co. (naam leverancier) Swan Lane, Hindley Green, Wigan WN2 4EZ (adres) verklaren, onder onze uitsluitende aansprakelijkheid, dat het produkt: Typen 7803R–EU Omkeerbare Boormachines voor Zwaar Werk waarop deze verklaring betrekking heeft overeenkomt met de bepalingen van directieven: 98/37/EG EN292 ISO8662 overeenkomstig de volgende hoofdstandaards: (1994 →...
- Página 19 All manuals and user guides at all-guides.com MAINTENANCE INSTRUCTIONS SECTION D’ENTRETIEN WARTUNG SEZIONE DI MANUTENZIONE INSTRUCCIONES DE MANTENIMIENTO ONDERHOUD (TPB855–1)
- Página 20 Reverse Valve Assembly ..7802R–A329 Spindle ....7803R–8 Reverse Valve Seal ..7802R–67 + 39 Spindle Planet Gear (3) .
- Página 21 All manuals and user guides at all-guides.com Lorsque les pignons du porte–satellites (31) et /ou les pignons satellites de la broche (39) sont remplacés, vous devez commander un kit de roulement de pignon satellite No. 7803–K10. Le kit de roulement de pignon satellite contient 45 aiguilles de roulement et 10 rondelles de retenue, quantités suffisantes pour 5 pignons.
- Página 22 All manuals and user guides at all-guides.com Service Centers Centres d’entretien Ingersoll–Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 45220 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House, TN 37188 PO Box 3720...
- Página 23 All manuals and user guides at all-guides.com...
- Página 24 EKSTRA KRAFTIGE, REVERSIBLE BOREMASKINER, MODEL 7803R OG 7803R–EU BEMÆRK Reversible boremaskiner model 7803R og 7803R–EU er designet til boring, honing, fræsning og hul- savning. Ingersoll–Rand påtager sig intet ansvar for eventuelle ændringer af værktøjer udført af brugeren i forbindelse med anvendelsesområder, som Ingersoll–Rand ikke på forhånd er blevet konsulteret om.
-
Página 25: Specifikationer
Borepatrons- hastighed kapacitet dB (A) niveau •Effekt o/min. tommer (mm) Tryk 7803R, 7803R–EU reversibel, 1/2 (13) 92,9 105,9 pistolgreb Afprøvet i overensstemmelse med ANSI S5.1–1971 ved fri hastighed ♦ Afprøvet i overensstemmelse med ISO8662–1 ved 80% af dimensioneret fri hastighed •... - Página 26 (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig, at nedenstående produkt, Ekstra kraftige, reversible boremaskiner, model 7803R–EU som denne erklæring vedrører, overholder bestemmelserne i følgende direktiver 98/37/EF ved at være i overensstemmelse med følgende hovedstandard(er): EN292 ISO8662 (1994 →) XUA XXXXX →...
- Página 27 REVERSIBLA BORRMASKINER, MODELLER 7803R OCH 7803R–EU OBS! Reversibla borrmaskiner, modeller 7803R och 7803R–EU är tillverkade för borrning, finslipning, upprymning och utsågning av hål. Ingersoll–Rand är inte ansvarigt för verktyg som har modifierats av kunden för att anpassas till andra användningar, om inte kunden har konsulterat Ingersoll–Rand.
- Página 28 Hastighet nivå dB (A) •Kraft varv/min. mm (tum) Tryck 7803R, 7803R–EU reversibel, pistol 13 (1/2) 92,9 105,9 G Testad i enlighet med ANSI S5.1–1971 vid fri hastighet ♦ Testad i enlighet med ISO8662–1 vid 80% beräknad fri hastighet •...
-
Página 29: Försäkran Om Överensstämmelse
Ingersoll–Rand, Co. (leverantörens namn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adress) intygar härmed, i enlighet med vårt fullständiga ansvar, att produkten, Reversibla borrmaskiner, modeller 7803R–EU som detta intyg avser, uppfyller kraven i 98/37/EG Direktiven. EN292 ISO8662 Genom at använda följande principstandard: (1994 →... - Página 30 EKSTRA KRAFTIGE, REVERSERBARE, TRYKKLUFTDREVNE DRILLER, MODELL 7803R OG 7803R–EU MERK Ekstra kraftig reverserbare trykkluftdrevne driller, modell 7803R og 7803R–EU er konstruert for boring, honing, opprømming og hullsaging. Ingersoll–Rand er ikke ansvarlig for verktøymodifikasjoner som utføres av kunden uten at Ingersoll–Rand er rådspurt.
-
Página 31: Spesifikasjoner
Hastighet Chuck–kapasitet sjonsniva dB (A) •Styrke o/min mm (tomme) Trykk 7803R, 7803R–EU reversibel, pistol 13 (1/2) 92,9 105,9 G Testet i følge ANSI S5.1–1971 ved fri hastighet ♦ Testet i henhold til ISO8662–1 ved 80 % nominell fri hastighet •... -
Página 32: Konformitetserklæring
Ingersoll–Rand, Co. (leverandørens navn) Swan Lane, Hindley Green, Wigan WN2 4EZ (adresse) erklærer som eneansvarlig at produktet, reverserbare trykkluftdrevne driller, modell 7803R–EU som denne erklæringen gjelder for, oppfyller bestemmelsene i EU–direktivene 98/37/CE EN292 ISO8662 ved å bruke følgende prinsipielle standarder: (1994 →... - Página 33 OHJEITA TPD1459 7803R– JA 7803R–EU –SARJAN ERIKOISVAHVOILLE ILMAPORAKONEILLE HUOMAA 7803R– ja 7803R–EU –sarjan porakoneet on tarkoitettu poraustöihin, hoonaukseen, avarrukseen ja reikien sahaamiseen. Ingersoll–Rand ei ole vastuussa työkalujen mahdollisista modifikaatioista muihin sovelluksiin, joista Ingersoll–Randille ei ole tiedoitettu. VAROITUS OHJEISSA ON MUKANA TÄRKEITÄ TURVAOHJEITA.
- Página 34 GMelutaso ♦Värinä Malli Kädensija– Vapaa Istukan tyyppi nopeus koko dB (A) •Teho 1/min mm (tuumaa) Paine 7803R, 7803R–EU kaksisuuntainen, 13 (1/2) 92,9 105,9 pistooli G Koestettu ANSI S5.1–1971 mukaisesti vapaalla kierrosnopeudella ♦ Koestettu ISO8662–1 mukaisesti 80%:sella vapaalla kierrosnopeudella • ISO3744...
- Página 35 Ingersoll–Rand, Co. (toimittajan nimi) Swan Lane, Hindley Green, Wigan WN2 4EZ (osoite) vakuutamme ja kannamme yksin täyden vastuun siitä, että tuote 7803R–EU –sarjan suunnanvaihtomekanismilla varustetut ilmaporakoneet johon tämä vakuutus viittaa, täyttää direktiiveissä 98/37/EY EN292 ISO8662 esitetyt vaatimukset seuraavia perusnormeja käytettäessä: (1994 →...
-
Página 36: Usando A Ferramenta
TRABALHOS PESADOS MODELOS 7803R E 7803R–EU TPD1459 AVISO Os berbequins Reversiveis Modelos 7803R e 7803R–EU são concebidos para perfuran, afiar a largan e cortar fanos A Ingersoll–Rand não é responsável por modificações, feitas pelo cliente em ferramentas, nas quais a Ingersoll–Rand não tenha sido consultada. -
Página 37: Colocando A Ferramenta Em Funcionamento
Livre Encabadouro dB (A) Punho Vibrações •Potência mm (pol.) Pressão 7803R, 7803R–EU pistola 13 (1/2) 92,9 105,9 Testada de acordo com a ANSI S5,1–1971 com velocidade livre ♦ Testada de acordo com a ISO8662–1 com 80% da velocidade livre •... -
Página 38: Declaração De Conformidade
(nome do fornecedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (endereço) declaramos sobre nossa única responsabilidade que o produto, Berbequins Pneumáticos Reversíveis Modelo 7803R–EU ao(s) qual(is) esta declaração se refere, está (ão) de acordo com as provisões da 98/37/CE Directivas EN292 ISO8662 Ao se utilizar os seguintes Princípios Standards:... - Página 39 All manuals and user guides at all-guides.com...
- Página 40 All manuals and user guides at all-guides.com...
- Página 41 All manuals and user guides at all-guides.com...