Publicidad
Idiomas disponibles
Idiomas disponibles
E - PREPARATION FOR USE
360 Grill :
A - Plastic lid :
The plastic lid is fastened on the top of the firebox thanks to
clips (Fig. 2). He keeps all the inside parts in place during
the transport. Remove it before use.
B - Use of the water tank :
Place the appliance on a flat ground. Fill the tank with water
till the MAX setting. (Fig. 3A) Pay attention not to spill water
on the burner.
After the cooking session, you may disconnect the water
tank to throw the mixture of water and grease and clean
it. You can use a sponge impregnated with non-abrasive
detergent product or put the tank in the dishwasher.
Disconnect the water tank by pulling the lock button (10).
Keeping the button pulled till its stop setting, remove the
tank by moving it upwards. (Fig. 3B)
After the cleaning, put the tank back on the base:
1- Pull the lock button (10) (Fig. 3C)
2- Align the flame viewing window (11) with the control knob
(9). The notches (12) of the base of the tank must be
aligned with the locking axle (13) (Fig. 3D)
3- Place the tank on its support
4- Release the button, the tank is locked (Fig. 3E)
Fill in the tank with water till the MAX setting if you want to
use it again. (Fig. 3A)
C - Pan support :
Put the pan support in place. Pay attention to insert the 3
notches of its base in the 3 flaps of the center of the firebox.
The rotation of the support is blocked. Your appliance is
GB
ready to be used as a stove. (Fig. 4)
D - Heat diffuser :
Place the heat diffuser on the top of the arms of the pan
support aligning the notches of its 3 supports with each arm
of the support. (Fig. 5)
E - Cooking griddle :
Place the cooking griddle on its 3 supports on top of the
firebox, paying attention to put the surface that you wish on
the top. (Fig. 6A & 6B)
Cartridge support :
Your appliance is supplied with a cartridge support. This
support allow you to fasten the cartridge at the edge of the
table. Thus, the cartridge is far away from the source of heat
and the surface of the table is free of it.
- Place your appliance at the center and unroll the hose till
the edge of the table.
- Fasten the cartridge support on the edge of the table. The
length of the setting screw allows an adaptation to most of
the tables. (Fig. 8)
Unscrew the setting screw (14) so that the space between
the 2 rubber pads fits the thickness of the frame of your
table (Fig. 9A), slice the support on the edge of your table
then tighten the screw to ensure a safe fastening to the
table. (Fig. 9B)
- Make the pusher (15) slide towards the top and insert the
regulator in the housing designed for this purpose. (Fig.
10A & 10B)
- Let the pusher go down, thus the regulator is maintained in
place thanks to the spring. (Fig. 10C)
- Check that the hose is unrolled freely, without any torsion
or traction, neither contact with hot surfaces of the
appliance. (Fig. 11) Never pull on the hose or twist it.
SAFETY PRECAUTIONS
Do not use your appliance at a distance of less than 20 cm
from a wall or a combustible object.
Position the appliance on a stable, horizontal surface and
do not move when in use to avoid the appearance of large
flames resulting from the combustion of liquid butane
rather than vaporised butane. Should this occur, turn off
the control knob, and re-position the appliance.
Do not use a cooking vessel smaller than 12 cm or larger
than 26 cm in diameter.
Before lighting the appliance in Grill or Plancha setting,
make sure to fill the reservoir with water to "MAXI" level.
Protect your appliance from wind, its performances will be
increased.
Never leave the cooking plate on fire without foodstuffs
longer than one minute (except for the initial pre-heating
period) otherwise the special coating will be damaged.
To avoid damaging the non-stick coating, always use
cooking utensils in silicone or wood to manipulate your
dishes.
Wait until the device has completely cooled down before
preparing it for storage.
Caution: some parts may be very hot. Keep young
children away from the appliance.
It is recommended that protective gloves be worn to
handle components which may be very hot.
Never use the appliance until the instructions have been
read carefully and understood. Additionally, ensure that:
- there are no leaks.
- make sure the burner tube is not obstructed (by spider
webs, etc.).
- the hose does not touch any components which may get
hot.
Important : check the presence of flame through the
window located on the firebox over the control knob (11)
(Fig. 1A). In case the burner extinguishes whilst grilling,
close the gas valve immediately and wait 5 minutes to let
the gas be evaporated. Re-ignite the appliance after this
waiting time.
6
Publicidad
