Briggs & Stratton VANGUARD 10V000 Manual Del Operador página 7

Manual Throttle Control
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 4).
Remote Throttle Control with Braided Wire Cable
A remote throttle control with a braided wire cable can be installed in one of two
directions: Cylinder Head Direction or Front Direction.
Cylinder Head Direction
1.
Move the throttle control / TransportGuard
2. Use a 10 mm wrench and loosen the nut (P, Figure 5) ½ turn on the throttle control /
®
TransportGuard lever (A).
3. Hold the cable mounting nut (J, Figure 6) with a 10 mm wrench and loosen the
screw (K).
4. Install the cable wire (L, Figure 6) through the hole in the cable mounting nut (J),
and tighten the screw (K). Make sure that the cable wire (L) does not extend more
than ½" (12,7 mm) past the hole.
5. Loosen the screw (I, Figure 6). Attach the cable sleeve (N) under the cable clamp
(M), and tighten the screw (I).
6. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that remote throttle control and the cable
wire (L, Figure 6) moves freely. Adjust the nut (P, Figure 7) as necessary for the
specified position.
Front Direction
1.
Adjust the throttle control / TransportGuard
a. For 10V000 and 12V000 engine models: Move the throttle control /
™
TransportGuard lever (A, Figure 8) to the FAST position.
b.
For 25V000 engine models: Move the throttle control / TransportGuard
(A, Figure 8) to the OFF position.
2. Use a 10 mm wrench and loosen the nut (P, Figure 7) ½ turn on the throttle
®
control / TransportGuard lever (A).
3. Hold the cable mounting nut (J, Figure 8) with a 10 mm wrench and loosen the
screw.
4. Install the cable wire (L, Figure 8) through the hole in the cable mounting nut (J)
and tighten the screw (K). Make sure that the cable wire (L) does not extend more
than ½" (12,7 mm) past the hole.
5. Loosen the screw (I, Figure 8). Attach the cable sleeve (N) under the clamp (M) and
tighten the screw (I).
6. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the cable
(L, 8) moves freely. Adjust the nut (P, Figure 7) as necessary for the specified
position.
Remote Throttle Control with Solid Wire Cable
A remote throttle control with a solid wire cable can be installed in one of four directions:
Cylinder Head Direction, Front Direction, Left Direction, or Right Direction.
Cylinder Head Direction
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 9).
3.
Move the throttle control / TransportGuard
4. Use a 10 mm wrench and loosen the nut (P, Figure 4) ½ turn on the throttle control /
®
TransportGuard lever (A).
5. Install the Z-fitting of the solid wire cable (Q, Figure 9) to one of the small holes in
the bellcrank (R).
6. Loosen the screw (I, Figure 9). Attach the cable sleeve (N) under the cable clamp
(M), and tighten the screw (I).
7. Check the operation of the remote throttle control. Move the remove throttle control
from slow to fast 2-3 times. Make sure that remote throttle control and the cable
wire (L, Figure 9) moves freely. Adjust the nut (P, Figure 4) as necessary for the
specified position.
Front Direction
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 10).
3.
Move the throttle control / TransportGuard
position.
4. Use a 10 mm wrench and loosen the nut (P, Figure 4) ½ turn on the throttle
®
control / TransportGuard lever (A).
®
lever (A, Figure 4) to the OFF position.
™
lever (A, Figure 5) to the OFF position.
™
lever:
™
lever
®
lever (A, Figure 9) to the OFF position.
®
lever (A, Figure 9) to the FAST position.
®
lever (A, Figure 10) to the OFF position.
®
lever (A, Figure 10) to the FAST
5. Install the Z-fitting of the solid wire cable (Q, Figure 10) to one of the two small
holes in the bellcrank (R).
6. Loosen the screw (I, Figure 10). Attach the cable sleeve (N) under the clamp (M)
and tighten the screw (I).
7. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the
cable (L, Figure 10) moves freely. Adjust the nut (P, Figure 4) as necessary for the
specified position.
Left Direction
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 4).
3.
Move the throttle control / TransportGuard
position.
4. Use a 10 mm wrench and loosen the nut (P, Figure 4) ½ turn on the throttle
®
control / TransportGuard lever (A, Figure 11).
5. Remove the throttle control knob (W, Figure 11) to get to the small hole (S).
6. Install the Z-fitting of the solid wire cable (L, Figure 11) to the small hole (S) in the
throttle control lever (A).
7. Loosen the screw (I, Figure 11). Attach the cable sleeve (N) under the clamp (M)
and tighten the screw (I).
8. Check the operation of the remote throttle control. Move the remote throttle control
from slow to fast 2-3 times. Make sure that the remote throttle control and the
cable (L, Figure 11) moves freely. Adjust the nut (P, Figure 4) as necessary for the
specified position.
Right Direction
To install a remote throttle control from the right direction, a cable mounting bracket
(U, Figure 12) is required. Refer to the Specifications and Service Parts section for
the part number. To purchase a cable mounting bracket, contact a Briggs & Stratton
Authorized Service Dealer.
1.
Move the throttle control / TransportGuard
2. Remove the spring (S, Figure 4).
3. Remove the throttle control knob (W, Figure 12) to expose the small hole (S).
4.
Move the throttle control / TransportGuard
position.
5. Use a 10 mm wrench and loosen the nut (P, Figure 4) ½ turn on the throttle
®
control / TransportGuard lever (A, 12).
6. Install the Z-fitting of the solid wire cable (L, Figure 12) to the small hole (S) in the
throttle control lever (A).
7. Remove the bolt (T, Figure 12). Install the cable mounting bracket (U) as shown.
Attach the cable mounting bracket (U) with the bolt (T). Tighten the bolt (T) to 30 lb-
in (3,4 Nm). Refer to the Specifications and Service Parts section.
8. Loosen the screw (I, Figure 12). Attach the cable sleeve (N) under the clamp (M)
and tighten the screw (I).
9. Examine the operation of the remote throttle control. Move the remote throttle
control from slow to fast 2-3 times. Make sure that the remote throttle control and
the cable (L, Figure 12) moves freely. Adjust the nut (P, Figure 4) as necessary for
the specified position.
Fixed Engine Speed (No Throttle Control Cable)
When converted to a Fixed Engine Speed, a throttle control cable is not installed and
there is no speed selection. FAST is the only engine speed.
1. Move the throttle control / TransportGuard® lever (A, Figure 13) to the OFF
position.
2. Remove the spring (S, Figure 13).
3.
Move the throttle control / TransportGuard
position.
4. Make sure the wire retainer screw (V, Figure 13) aligns with the hole in the bracket.
Tighten the screw (V) to 25 lb-in (2,8 Nm).
5. Remove the control link (H, Figure 13).
NOTE: At this time, the throttle control / TransportGuard
positions: STOP / OFF position and RUN position.
6.
Install the new ON / OFF TransportGuard
speed control label located on the trim panel (F).
®
lever (A, Figure 11) to the OFF position.
®
lever (A, Figure 11) to the FAST
®
lever (A, Figure 12) to the OFF position.
®
lever (A, Figure 12) to the FAST
®
lever (A, Figure 13) to the FAST
®
lever will only have two
®
label (O, Figure 14) over the existing
7