Chicco 360 SEAT Manual De Instrucciones página 11

Do not tumble dry
Do not iron
Do not dry clean
COMPONENTS
a. Frame (fixed section)
b. Seat with fabric (rotating section)
B1. Button to release the seat from the frame
B2. Plastic tabs for fastening the seat to the frame
B3. Child restraint belt
B4. Restraint belt buckle
B5. Tabs for fastening the fabric to the seat
C. Arms with non-slip rubber
C1. Metal pins for fastening to the frame
D. Fastener clamps
D1. Rubber fastening pins
D2. Buttons for releasing pins
D3. Buttons for locking pins
FIRST ASSEMBLY
1. Pull the product out of the bag.
2. Position the frame "A" on a level surface. Incline the seat with the
fabric "B" just a little to insert the plastic tabs "B2" into the frame
"A" (Fig. 1). Press down on the rear section of the seat "B" to lock
it into place (Fig. 2). Verify that the tabs are under the frame "A"
(Fig. 3).
3. Flip the resulting structure upside down. Press the metal pins
"C1" on the arms with non-slip rubber "C" and insert the arms
into the frame one at a time (Fig. 4). Once the arms have been
inserted, verify that the pins "C1" emerge from the holes on the
frame (Fig. 5).
4. Keep the product upside down and insert the fastening clamps
"D" into the bottom part of the frame "A" being careful to pair
the letters found on the pins with those found on the frame (Fig.
6). During insertion, two metal pins (Fig. 7) will need to snap into
place for each side.
USE
5. If there is insufficient space between the pins "D1" and the arms
"C", press the release buttons "D2" on the two pins to lower
them (Fig. 8). You may need to gently press the two pins down-
wards, in order to create an opening.
6. Slide the seat onto the tabletop (Fig. 9). If there are obstacles on
the underside of your table, be sure that the pins are fixed in place
beyond the obstacle (Fig. 10).
WARNING: Make sure there are no gaps between the seat and the
tabletop (Fig. 11).
7. To fasten the seat to the table press the two buttons "D3" until
the pins "D1" have come into complete contact with the under-
side of the table (Fig. 12).
8. Verify that the arms with non-slip rubber "C" lie flat and adhere
fully to the upper surface of the table (Fig. 13). If they don't adhere
completely, press the buttons "D3" again.
WARNING: Verify correct installation on the tabletop by attempting
to pull the seat outwards. At this point, the seat is ready to be used.
USING THE SAFETY HARNESS
9. After having placed your baby in the seat always fasten the safety
belts by fastening the buckle "B4" (Fig. 14). The length of the belt
"B3" can be adjusted by pulling the belt through the ladder lock
(Fig. 15).
SEAT ADJUSTMENT
The seat can be rotated 360°, it can be adjusted in 4 different posi-
tions (Fig. 16).
10. To adjust the position of the seat "B" take hold of the seat from
the top with two hands and rotate clockwise or anticlockwise
until you reach the desired position (Fig. 17).
WARNING: do not adjust the seat to a position of use other than
those indicated in this instruction booklet. The seat must never be
adjusted while the child is sitting in it. In this case it can be slightly
more difficult.
WARNING: While adjusting the seat, make sure that the child's legs
can freely follow the movement of the seat.
REMOVING THE SEAT FROM THE TABLE
11. To remove the seat from the table press the pin release buttons
"D2" (Fig. 18). If the release buttons are difficult to press, press
gently on the pin lock buttons "D3" while simultaneously press-
ing on the release buttons "D2" (Fig. 19).
12. Pull the seat off of the tabletop (Fig. 20).
WARNING: Do not remove the seat from the table with the child
seated inside.
CLOSING THE SEAT
13. To make the product as compact as possible the two fastening
clamps "D" can be folded inwards by pressing on the pins and
rotating them (Fig. 21-22).
REMOVING THE FABRIC
The seat fabric can be taken off of the table seat and washed.
14. Disconnect the seat "B" from the frame "A" using the release
button "B1" (Fig. 23).
15. Flip the seat "B" upside down and press down on the fabric
through the frame of the seat (Fig. 24).
16. Raise, rotate, and press the eight tabs "B5" through the slots to
extract them from the seat "B" (Fig. 25-26-27-28).
17. Remove the fabric from the frame (Fig. 29)
18. Remove the panel on the base of the seat from the fabric (Fig. 30).
The fabric can now be washed following the instructions provided
in the "MAINTENANCE SUGGESTIONS" paragraph.
To fit the fabric cover back on the seat, repeat the steps illustrated
above in reverse order. Be sure to align the fabric and the seat frame
correctly. Specifically, start from the tab found next to the Chicco
logo on the backrest and insert it into the slot located next to the
number 1 (Fig. 31). Continue with all the other tabs being sure that
each tab adheres firmly to the recess into which it is inserted (Fig.
32-33).
DISASSEMBLY AND TRANSPORT
Proceed as follows for product disassembly.
19. Remove the fastening clamps "D" by pressing on the lower pin
and rotating the clamp a little (Fig. 34). Next, press on the other
pin and pull out the clamp (Fig. 35). Repeat the operation with
the other clamp.
20. Remove the arms "C" by pressing on the pin and pulling them
out of the frame (Fig. 36).
21. All the components of the product can now be placed inside the
bag for transportation.
WARRANTY
The product is guaranteed against any conformity defect in normal
conditions of use as provided for by the instructions for use. The
warranty shall not therefore apply in the case of damages caused by
improper use, wear or accidental events. For the duration of warran-
ty on conformity defects please refer to the specific provisions of na-
tional laws applicable in the country of purchase, where provided.
11