Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component of the
product. Therefore, please store them and the packaging carefully in case questions arise
in the future. Please always include these instructions when handing on the product to a
third party. This product must be assembled by an adult. This product is not designed for
industrial use. The use of the product requires specific skills and knowledge to be able to
avoid injuries due to crashes and collisions. Always adjust according to the age of the user
and use for the purpose it has been designed for.
TECHNICAL SPECIFICATIONS
Item: Tricycle SX-0,9"
Item number: 10284
Dimensions when assembled: 77 x 48 x 100 cm
Maximum carrying capacity: 20 kg
If you have assembly problems or would like further information on the product, we have
all you need and more at http://www.hudora.de/.
CONTENTS
1
2
6
7
1.
Front wheel fork with front wheel
2.
Front protective shield
3.
Frame with bottom steering cover
4.
Tipping trough with axle and connecting screws
5.
Rear wheels (2x)
6.
Handle bar with steering screw and upper steering shield
7.
tool
8.
Seat screw
9.
Seat
10.
Pushing rod, two parts
Other parts which may be included with the delivery in some circumstances are not
required.
SAFETY INSTRUCTION
The tricycle should only ever be used under adult supervision. Please use the tricycle in
suitable play areas only. It does not correspond with road traffic regulations. It may not be
used on the road and should not be used in the dark.
The tricycle corresponds with the provisions of the European norm EN 71 and therefore
bears the CE symbol. When used as intended, risks during play are excluded to a large
degree. However, please consider that unforeseeable situations and risks can arise due
to children's natural play instinct and temperament and are not the manufacturer's re-
sponsibility. Therefore, please instruct your children on the correct use of the tricycle
and mak them aware of any possible risks. Do not allow two children to ride the tricycle
simultaneously under any circumstances.
Children should wear protective clothing and closed shoes. Please do not use the tricycle
in the proximity of stairs, slopes, steep ground, swimming pools or other areas of open
water. Stairs in the vicinity should be blocked off so that children can never cycle
ASSEMLBY
Remove the individual pre-assembled parts from the box and check that they are
complete. You will need a Phillips head screw driver for the assembly.
STEP-BY-STEP ASSEMBLY
1. Guide the front protective shield
2
the longer end of the protective shield is positioned on the side where the fork has a
round hole. The short end will later point into the driving direction where the fork has
a square hole.
2. Insert the fork
through the frame
1
3. Remove the screws from the bottom steering cover. These will once again be required
in a later step!
All images are examples of the design.
All manuals and user guides at all-guides.com
4
3
8
9
over the front wheel fork
in such a manner that
1
from the bottom.
3
HUDORA I Jägerwald 13 I 42897 Remscheid I Germany
4. Loosen the nut on the handle bar
bar into the fork from the top.
5. Insert the steering screw from the front through both tubes and pull the nuts tight.
6. Next, insert the screws you removed during step 3 into the upper cover and screw them
tightly into the bottom cover.
7. Loosen the screw from the red connecting sleeve at both rear wheels
will be needed again in step 9! The other components of the rear wheels must be left
assembled.
8. Insert the connecting sleeve with its edge pointing toward the wheel into the axle. Next,
insert one wheel sleeve into the axle so that the grooves of the wheel sleeve fit snugly
into the notches of the axle.
9. Next, insert the wheel into the axle and screw the connecting sleeve in place using
the screw from step 7 so that the wheel is locked in tightly! Repeat steps 7-9 for the
third wheel.
10. Loosen the tipping trough by placing slight pressure on the back rear axle
loosen the connection screw required in step 11.
11. Mount the frame
3
to rear wheel axle
10.
12. Click the tipping trough into place in the three designated positions on the frame.
13. Mount seat
to frame
9
14. Insert the two components of the pushing rod
assembly to frame
behind the seat. Make sure that the pressure buttons do jump
3
back out to warrant that the seat is firmly in place.
15. The mount for the parents' push bar has a cover. If you are not using the push bar,
close the opening with the protective cap to prevent dirt and moisture from entering
5
the frame.
After you have assembled all components, make sure that all connections are tightly
screwed together before allowing your child to play with the tricycle.
10
You should also check before each use that all of the parts are tightly joined to one
another. For your own safety, you should immediately replace damaged parts. Original
replacement parts are recommended or you should ask an expert to advise you in
relation to this. Subject to technical changes.
MAINTENANCE AND STORAGE
Check the product for damage or traces of wear and tear before and after each use.
We also recommend before each use:
• to check for the firm sitting of nuts and bolts, tighten if necessary
• to lubricate moving parts in order to minimize wear.
• to check all covers of screws and sharp edges and replace if necessary
• to replace defective parts according to the manufacturer's instructions
The constant exposure to sunlight can lead to fading of the color, due to UV light that has
however no hazardous safety aspect.
Use a dry or damp cloth only to clean the product; do not use special cleaning agents!
Store the product in a safe place where it is protected from the elements, cannot be da-
maged, and cannot injure anyone. If parts become damaged or if sharp edges or corners
should develop, the product may not be used any more. If in any doubt, please contact our
service team (http://www.hudora.de/service/).
DISPOSAL ADvICE
At the end of the product's life, please dispose of it at an appropriate collection point in
your area. Local waste management companies will be able to answer your questions
on this.
SERvICE
We make every effort to deliver faultless products. If faults do arise however, we put
just as much effort into rectifying them. Therefore, you can find numerous information
on the product, replacement parts, solutions to problems and lost assembly manuals at
http://www.hudora.de/artnr/10284/.
www.hudora.de
and remove the steering screw. Insert the handle
6
with the two connecting screws from step
4
with seat screw
.
8
3
into each other and mount the
10
. This screw
5
. Also
4
Art.-Nr. 10284
As of 03/12
Page 4/8
Publicidad
