Preparing For Work; Product Operation - YATO YT-82360 Manual Original

EN
be avoided by following the instructions below.
Use a fi rm grip on the tool and the correct body posture and hands position to withstand the forces generated by the
kickback. Always use an additional handle, if supplied with the tool, to ensure maximum control during the kickback or
any unexpected rotation during the tool start. The operator will be able to control the tool rotation or the kickback if appropriate
precautions are taken.
Keep your hands away from rotating tool parts. The rotating parts can come into contact with your hands during kickback.
Do not stand in the area where the tool may move during the kickback. The kickback will direct the tool in the opposite direc-
tion to the direction of the grinding wheel rotation, at the jamming point.
Pay special attention when working near corners, sharp edges, etc. Prevent the grinding wheel from runout and being
jammed. When machining corners or edges, there is an increased risk of the grinding wheel jam, leading to a loss of control or
tool kickback.
Do not use discs with a cutting chain for wood processing, segmented diamond discs with circumferential spacing be-
tween segments greater than 10 mm or discs with teeth. Such discs cause frequent kickbacks and loss of control of the tool.
Warnings related to grinding with sandpaper
Use the correct size sandpaper. When selecting a disc, follow the manufacturer's recommendations. A sandpaper that
protrudes well beyond the disc may cause injury, and also increase the risk of jamming, tearing or kickback towards the operator.

PREPARING FOR WORK

Warning! All adjustment and preparation for work shall be done with the tool isolated from live voltage. Make sure that the battery
has been disconnected from the tool socket.
Handle extension arm installation (II)
The sander comes with a handle extension arm. The extension arm is mounted at the end of the handle.
Before assembly, pull the lever at the end of the handle. Insert the extension arm so that it is inside the handle and press the lever.
Check that the extension arm does not move inside the handle.
There may be a mark on the extension arm which indicates the length to which it can be extended. Do not exceed the allowable
extension arm length. If you do, this can cause the extension arm to slip out of the sander handle spontaneously, which can cause
damage to the product and also lead to injury.
If there is no marker, at least 15 cm of the extension arm must be placed inside the handle.
To remove the extension arm, follow the above procedure in the reverse order.
Dust extraction hose installation (III)
The sander features a fl exible hose with a bag to collect dust generated during operation.
Connect the hose to the end of the handle or to the end of the handle extension arm. When mounting to the extension arm, pull the
lever at the end of the extension arm. Install so that the bayonet connector prevents the hose from disconnecting during operation
and press down on the lever.
The sander has a fan which directs dust generated during operation to the bag.
The dust bag has a roll closure which allows the bag to be emptied. The bag fi lling level should be checked during operation and
the bag itself emptied each time the dust extraction effi ciency decreases. The bag should not be rolled further than the place
marked with lines and arrows.
The bag can only be emptied when the sander is switched off . The power cord plug must be unplugged from the electric outlet.
The hose attached to the sander does not allow disassembly of the bag so as to connect the sander to an external dust extraction
system. If necessary, the sander should be equipped with a separate hose.
Mounting the sandpaper sheet (IV)
Caution! Make sure the sandpaper sheet is free from damage before installing it. If you notice any damage in the form of folds,
cracks, tears or holes, replace the sheet with a new one which is free of damage.
The sandpaper sheet must be provided with a surface which allows it to be attached on the disc by means of Velcro pad. The
sheets should have holes in the same places as the holes in the tool disc. Only then will it be possible to extract the dust generated
during operation eff ectively.
Place the sheet on the disc coaxially so that the holes in the sheet match the holes in the tool disc. The edge of the sandpaper
disc must not come into contact with the tool guard or the peripheral brush of the guard.

PRODUCT OPERATION

Caution! All the assembly steps described above must be carried out before beginning operation.
O R I G I N A L I N S T R U C T I O N S
17