Connecting To The App - Roborock Q7+ Manual Del Usuario

to prevent personal injury or
property damage due to items
becoming tangled in, struck by, or
knocked over by the robot.
B1-2—When using the robot in a raised area,
always use a secure physical barrier to
prevent accidental falls that may result
in personal injury or property damage.
Note: When using the robot for the first time, follow it throughout
its whole cleaning route and watch for potential problems. The
robot will be able to clean by itself in future uses.
Position the dock
B2
B2-1—Take the screwdriver from its storage
bin at the bottom of the base.
B2-2—Place dock upside down on a soft,
flat surface (carpet/towel/cloth)
and attach the base by using the six
screws provided.
Note: Hold the dustbin cover securely when upside down to
prevent damage from falling.
B2-3—Connect the power cable to the dock,
and keep the excess cable inside the
storage slot.
B2-4—Place the dock on a hard and flat
floor (wood/tile/concrete etc.). Keep
at least 0.5 m (1.6 ft) of clearance
on either side, 1.5 m (4.9 ft) in front,
and 1 m (3.3 ft) above. Check the
location has good WiFi then turn on.
B2-4-1—More than 0.5m (1.6ft)
B2-4-2—More than 1.5m (4.9ft)
B2-4-3—More than 1m (3.3ft)
Emptying
B3
Auto-emptying will begin when the robot
returns to the dock after cleaning. Press the
button to trigger emptying manually.
Press any button to stop emptying.
Notes:
• The status indicator light on the dock turns off automatically
when the robot is charging.
• Do not use without dustbin cover or dust bag.
• Place the dock on a flat floor away from fire, heat, and water.
Avoid narrow spaces or locations where the robot may be
suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may cause
the dock to tilt over and cause problems docking and
departing.
• Keep the excess power cable inside the storage slot so that
the robot will not get tangled in the cables, and the dock will
not be dragged away or disconnect from the power supply.
• Keep the dock away from direct sunlight or anything that
may block the dock location beacon; otherwise, the robot
may fail to return to the dock.
• The Auto-Empty Dock recharges and empties. Store the
standard robot dock before use. Failure to do so may cause
issues returning to dock.
• Maintain the dock according to the maintenance instructions.
Do not clean the dock with a wet cloth.
• Avoid frequent manual emptying.
• Images are for illustration purposes only and may not exactly
represent the product.
Using the mopping module
B4
B4-1—Adjust the water flow
Slide the switch down to increase the water
flow and up to decrease the water flow.
B4-2—Fill the water tank
Remove the water tank stopper, fill it with
water, and close it.
06
B4-3—Install the mop cloth
Dampen the mop cloth and wring it until it
stops dripping. Insert it into the bottom along
the attachment slot and stick it firmly in place.
B4-4—Install the mopping module
Slide the mopping module along the back
of the robot as indicated by the arrow. A
click indicates that it is locked in place.
Notes:
• To prevent excessive dirt buildup during first-time use, floors
should be vacuumed at least three times before mopping.
• If carpets are present, draw No-Go Zones or Invisible Wall to
prevent the robot going on them, or roll them up.
• To avoid water tank corrosion, do not use cleaning fluid or
disinfectant.
• The mop cloth should be cleaned after 60 minutes of
mopping to ensure water flow and cleaning performance.
Remove the mopping module
B5
When the robot returns to the dock after
cleaning, press the latches on both sides,
and slide the mopping module backwards
to remove it.
Notes:
• Wash the mop cloth after each use, and regularly empty the
water tank of unused water to prevent odor.
• Remove the mopping module when not mopping.

Connecting to the App

The robot supports the Roborock and Xiaomi
Home app. Choose the one that best meets
your needs.