Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING ‒ Risk of explosion!
Escaping gas may cause an explosion.
All Installation, connection, regulating and conver-
▶
sion work to a different gas type must be carried
out by an authorised professional while taking into
account the respective applicable regulations and
legal requirements as well as the regulations re-
garding the local electricity and gas suppliers.
Special attention must be paid to the provisions
and guidelines that are applicable for the ventila-
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
WARNING ‒ Risk of poisoning!
Harmful gases may be produced if combustion is in-
complete.
To ensure proper operation, sufficient combustion
▶
air must be supplied from the underside of the ap-
pliance. Ensure that there is a ventilation opening
in the unit under the appliance with a total area of
2
at least 100 cm
.
¡ Ensure that the kitchen is sufficiently ventilated, in
particular when operating the gas cooking appli-
ance.
¡ Do not connect the appliance to an exhaust gas
system for combustion products.
¡ Never install the appliance in boats or in vehicles.
¡ The warranty applies only when using the appli-
ance as intended.
¡ Before installing the appliance, check that the
local conditions of the supplier are compatible
with the appliance settings specified on the rating
plate (type of gas and pressure, power, voltage).
¡ Secure the power cord to the cabinet to prevent it
from touching hot parts of the oven or hob.
¡ Before any work is carried out on the appliance,
switch off the power supply and the gas supply.
¡ Connect the appliance to the power supply using
the earth.
¡ Do not make any changes to the inside of the ap-
pliance. If required, contact our technical cus-
tomer service.
Before installing
¡ This appliance is a class 3 appliance in accord-
ance with the EN 30-1-1 standard for gas appli-
ances: Built-in appliance.
¡ The unit in which the appliance is installed must
be stable and secured appropriately.
¡ The units in the vicinity of the appliance, the lamin-
ated panels and the adhesive with which they are
secured must be made of non-flammable, heat-
resistant materials.
¡ Do not install this appliance above refrigerators,
washing machines, dishwashers or similar.
¡ The appliance must only be installed on an oven
with forced ventilation. Check the dimensions of
the oven in the installation instructions for the
oven.
¡ If you install an oven underneath the hob, the work
surface thickness may differ from the dimensions
given in these instructions. Take note of the in-
formation in the oven installation instructions.
¡ If you install an exhaust air fan or an extractor
hood, refer to the installation instructions for these.
Always observe the minimum vertical distance to
the hob.
→ Fig.
1
Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions depending on the relevant installation
method: Standard (a) or flush (b).
→ Fig.
, → Fig.
2
3
12
¡ Seal the cut surfaces of wooden work surfaces
with a special glue seal to protect them from mois-
ture.
¡ If there is no built-in oven underneath the hob, in-
sert a non-flammable separator (e.g. metal or ply-
wood) at a distance of 10 mm from the hob. This
prevents access to the underside of the hob. The
distance from the intermediate floor to the mains
connection for the appliance must be at least 10
mm.
→ Fig.
, → Fig.
4
5
Preparing the furniture item for flush installation
¡ All cutting work on the work surface must be car-
ried out in a specialist workshop.
¡ The cuts must be clean and precise because the
cutting edge is visible on the surface. The stability
of the units must also be ensured after the cutting
work.
¡ Only use special, temperature- and water-resistant
work surfaces (e.g. natural stone or tiles).
¡ The fitted unit must be heat-resistant up to 90 °C.
Positioning the appliance
Note: Do not use silicone to bond the appliance to
the worktop.
Position the hob with the upper side facing down
1.
on a flat, stable surface.
Apply the adhesive seal supplied to the lower
2.
edge of the hob. The adhesive seal prevents the
penetration of liquids.
→ Fig.
6
Screw the brackets supplied into the specified po-
3.
sition so that they can turn freely.
→ Fig.
7
If you install the appliance in a 480 mm wide
4.
niche, you must remove the spacer, which is pre-
installed on the back of some models.
→ Fig.
8
Turn the hob around and insert it into the recess.
5.
Insert the hob in the front of the recess.
→ Fig.
9
Turn the brackets and tighten them fully.
6.
→ Fig.
10
The position of the brackets depends on the work-
top thickness.
Installing the appliance flush
Install the appliance so that there is an even gap
1.
all around it. → "Positioning the appliance",
Page 12
The hob should be slightly below the work sur-
‒
face. On tiled worktops, the contact surfaces
can be raised, if necessary, with temperature-
and water-resistant rails.
→ Fig.
11
Check that the appliance works correctly and is in
2.
the correct position.
Fill the gap between the work surface and the hob
3.
using a suitable commercially available silicone
adhesive.
→ Fig.
12
Smooth the silicone adhesive with a spatula or a
finger wetted with soap before a solid layer forms.
Note: Leave the silicone adhesive to dry before you
use the appliance.
Tip: If you use an unsuitable silicone adhesive on
natural stone work surfaces, it may cause discolour-
ation that can no longer be removed. A suitable ad-
hesive is available from our technical customer ser-
vice.
Publicidad
