Publicidad
Idiomas disponibles
Idiomas disponibles
Removing the appliance
Disconnect the appliance from the electricity and
1.
gas connections.
Unscrew the brackets and proceed in reverse or-
2.
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION ‒ Risk of explosion!
A gas leakage may cause an explosion.
If any connection is handled, check the seal.
▶
¡ Arrange the gas connection so that the shut-off
valve is accessible.
¡ Ensure that the information on the rating plate re-
garding the gas type and gas pressure complies
with the local connection conditions.
¡ Connect the appliance to a fixed gas pipe or a
flexible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the ap-
pliance is installed (e.g. a drawer) and must not
be routed through any spaces which might be-
come obstructed.
¡ Gas connection elbow on the appliance: R 1/2.
¡ Do not move or twist the gas connection elbow.
Spare parts for gas connection
You can obtain the gas connection parts from the
technical customer service.
Seal
Gas connection elbow: G 1/2
Gas connection R 1/2
→ Fig.
13
Gas connection G 1/2
Replace the gas connection elbow on the appli-
1.
ance with the gas connection elbow G 1/2 sup-
plied in the accessory bag.
→ Fig.
14
Insert the seal between the gas connection of the
2.
appliance and the gas supply.
→ Fig.
15
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
16
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Economy burner
Standard-output burner
Removing the outer glass plate
1.
2.
3.
Removing the circuit board
Tip: The circuit board is secured to the holder by
fastening pins at the sides and in the middle. Push
the fastening pins carefully without damaging them.
If one of the pins breaks, the entire holder must be
replaced.
ATTENTION!
The circuit board can be damaged by improper
handling.
▶
▶
▶
1.
2.
3.
00034308
→ Fig.
10006024
Adjusting the taps
Requirement: The upper part of the appliance and
the circuit board are removed. → "Removing the
outer glass plate", Page 13 → "Removing the cir-
cuit board", Page 13
1.
2.
Replacing the nozzles
1.
2.
3.
Reinstalling the appliance
▶
Checking if equipment is working
1.
shows the
25
2.
High-output burner
Mini-wok multi-crown burner
Wok multi-crown burner
Remove the pan supports, burner caps, distribut-
ors and rotary knobs.
Undo the screws on the burners.
Carefully remove the glass plate.
Handle the circuit board carefully.
Use anti-static shields or hold the circuit board at
the edges.
Never touch the surfaces of the circuit board on
which there are components or conducting tracks.
Undo the fastening pins on one side.
Release the fastening pins in the middle by press-
ing on them from both sides with your fingers.
Undo the fastening pins on the other side and re-
move the circuit board.
17
Remove the cylindrical parts and springs from the
fittings spindle.
When adjusting the bypass screws (M), refer to
the table → Fig.
.
25
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
18
On some appliances, the multi-crown burner may
have a metal plate attached to it. Unscrew and re-
move the metal plate.
→ Fig.
19
Replace the nozzles using the appropriate wrench
and tighten them carefully to guarantee the seal.
→ Fig.
, → Fig.
20
21
Ensure that the nozzle does not become detached
during removal or fastening.
If the appliance is equipped with a metal plate on
the wok burner, screw the metal plate back on.
Install the appliance components in reverse order.
Check that turning the rotary knob between the
position for maximum power and the position for
minimum power does not cause the burner to go
out or result in backfire.
If the gas flow from the burner is not correct, in
the table → Fig.
, check whether the nozzle and
25
the position of the bypass screw are correct.
13
Publicidad
