Product Familiarisation; Intended Use - Silverline 996048 Manual De Instrucciones

EN
Impact Driver Safety
WARNING!
• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
• Hold the power tool by insulated gripping surfaces, when performing an operation where
the fastener may contact hidden wiring or its own cord. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live" and could give the operator an
electric shock.
a) DO NOT allow anyone under the age of 18 years to use this tool. Ensure that operators are
qualified and familiar with the operating and safety instructions.
b) ALWAYS grip the tool firmly, DO NOT overreach, and ensure you won't lose control. Keep
secure footing whilst using an impact driver.
c) Battery chargers are for indoors use only. Ensure that the power supply and charger are
protected against moisture at all times.
d) When using the impact driver, use safety equipment including safety glasses or shield,
ear defenders, and protective clothing including safety gloves. If the work produces dust
wear respiratory protection suitable for the work being undertaken. A minimum rating of FFP2
is recommended. If operating the tool causes discomfort in any way, stop immediately and
review your method of use.
e) Ensure that the lighting is adequate.
f) Ensure that the impact driver bit or accessory is securely fixed in the bit holder. Insecure
accessories can be ejected from the machine causing a hazard.
g) DO NOT exert pressure on to the tool. To do so would shorten its service life.
h) If you are interrupted when operating an impact driver, complete the process and switch
off before looking up.
i) Where possible, use clamps or a vice to hold your work.
j) Examine the bit holder regularly for signs of wear or damage. Have damaged parts repaired
by a qualified service centre.
k) ALWAYS wait until the impact driver has come to a complete stop before putting it down.
l) Periodically check all nuts, bolts and other fixings and tighten where necessary.
m) Only use bits and accessories, specifically designed for use with impact drivers.
Conventional bits and accessories may shear off during use, or be otherwise damaged,
potentially ejecting dangerous projectiles.
n) Ensure that fasteners are suitable for impact driver use. Nuts, bolts and screws that are not
suitable for high torque application may be damaged.
o) Even when this tool is used as prescribed it is not possible to eliminate all residual risk
factors. If you are in any doubt as to the safe use of this tool, do not use it.
Battery and Charger Safety
Use the Battery Charger correctly
• Refer to the section of this manual relating to use of the Battery Charger (12) before attempting
to charge the Battery (7)
• Do not attempt to use the Battery Charger with any batteries other than those supplied.
• Keep your Battery Charger clean; foreign objects or dirt may cause a short or block air vents.
Failure to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard
• Examine the Battery Charger regularly for damage, especially the cord, plug and enclosure. If the
Battery Charger is damaged, it must not be used until it has been repaired
• Children should be supervised to ensure that they do not play with the appliance
WARNING: Do not attempt to recharge non-rechargeable batteries.
Battery safety
WARNING: Li-ion batteries, if incorrectly used, stored or charged are a fire, burn and explosion
hazard.
• Keep the battery out of reach of children
• Only charge Li-ion batteries designed specifically for this charger
• Only use Li-ion batteries provided with this product or specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these
instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure battery contacts cannot accidentally short in storage. Keep batteries clean; foreign objects
or dirt may cause a short. Keep away from other metal objects, for example paperclips, coins,
keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin
irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, seek medical help
• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire
or similar
• Do not get batteries wet or immerse in water
8
Battery & charger safety features
The Battery and Charger are fitted with a number of safety features which may be triggered during
charging or operation:
• Over-charge protection: Charger automatically switches off when the Battery has reached full
charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the Battery from discharging beyond the recommended
lowest safety voltage
• Over-heat protection: Sensor switches off if the Battery becomes too hot during operation.
This can happen if the tool is overloaded or being used for extended periods of time. Up to 30
minutes cooling time may be required depending on the ambient temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current draw is
exceeded, protecting the internal components. The Battery will resume normal operation when
the current draw returns to a normal safe level. This may take a few seconds
• Short circuit protection: The Battery will stop working immediately if a short circuit occurs, this
prevents damage to the Battery or tool

Product Familiarisation

1. Hex Bit Holder
2. Collar
3. Motor Vents
4. Direction Switch
5. Battery Mount
6. Battery Charge Indicator
7. Battery
8. Battery Release
9. ON/OFF Switch
10. On-Tool Battery Indicator
11. LED Light
12. Battery Charger
13. Red LED
14. Green LED
15. Charger Terminals

Intended Use

High torque, battery-operated impact driver for driving screws, nuts, bolts and other fasteners.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in this
manual will be considered a case of misuse. The operator, and not the manufacturer, shall be liable
for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable
for any modifications made to the tool, nor for any damage resulting from such modifications.
Unpacking Your Tool
• Carefully unpack and inspect your product. Fully familiarise yourself with all its features
and functions
• Ensure all parts of the product are present and in good condition
• If any parts are missing or damaged, have such parts replaced before attempting to use
this product
Before Use
WARNING: ALWAYS remove the battery before attaching or changing any accessories or making
any adjustments.
Removing the Battery
To remove the Battery (7), press the Battery Release (8) and slide the Battery off the Battery Mount
(5) (Fig. I (a-b))