08_Assembly; 09_Distance Adjustment Of Arion Digital Smart B; 10_Use; 11_Troubleshooting - Elite ARION DIGITAL SMART B+ Instrucciones

EN
N°1 Middle roller
N°1 Rear roller
N°1 Power adapter
N°1 Allen key

08_ASSEMBLY

Your Arion Digital Smart B+ roller should arrive fully
assembled, checked and ready for use.
09_DISTANCE ADJUSTMENT OF ARION
DIGITAL SMART B+
Before starting to use your Arion Digital Smart B+ it is
necessary to adjust the centre distance of the rollers to
make them compatible with your bicycle's wheelbase.
This adjustment must be carried out as follows:
1) Measure the distance between the centres of the whe-
els of the bicycle to be used on the Arion Digital Smart B+
(Fig. 2). We will call this dimension "X".
2) The distance from the intermediate point between the
two rear rollers to the middle of the Arion Digital Smart B+
front roller, which we will call "Y" (Fig. 3), must match or be
as near as possible to dimension "X" . The axle of the Arion
Digital Smart B+ front roller must be positioned in the hole
of the Arion Digital Smart B+ frame whose measurement
given on the graduated scale is closest to dimension "X"
(Fig. 4).
ATTENTION: dimension "Y" must be equal to or slightly
greater than "X". The rollers can be adjusted to adapt
them to bicycles whose wheelbase is 944-1124 mm
(37 to 44 inches).
3) To change Y it is necessary to shift the front roller F).
4) Fold the Arion Digital Smart B+ until the drive belt E)
slackens.
5) Loosen the drive belt E), making it come off the respec-
tive front and rear guides.
6) Unfold the Arion Digital Smart B+ back into the open
position.
7) Remove the rectangular covers C) from both front lon-
gitudinal members (with aid of a screwdriver if necessary),
and the screws and washers from the front roller on both
sides, using the allen key supplied (Fig. 5 and Fig. 6).
8) Pull the roller out from its original position.
9) Position the roller in the appropriate seat in the holes in
the frame, so that X matches Y.
10) Refit the screws and the washers in the special holes,
but do not tighten them down.
11) Close the Arion Digital Smart B+, position the drive belt
E) on the guide of the front roller F) and middle roller G).
12) Unfold the Arion Digital Smart B+ into open position
again.
13) Check the position of the front roller F), putting your
14
G bicycle on the rollers and checking that the axle for the
H front wheel sits directly above the front roller.
I 14) Once the front roller F) has been positioned, tighten the
screws without applying too much pressure which could
twist the A) side Frames.
15) Close the sides with the rectangular covers C). The
Arion Digital Smart B+ is now ready to use.
- Attention: integrated wireless systems that work on
the same frequency band can interfere with the data
transmission of the Arion Digital Smart B+. In this case,
deactivate them.
- Do not leave the roller and console exposed to direct
sunlight or in particularly humid places for prolonged
periods when not being used.
- Never use chemical detergents (petrol or thinners) on
any part of the Arion Digital Smart B+.

10_USE

- Plug the power adapter I) into a wall outlet and the con-
nector into the resistance unit (Fig. 7 and Fig. 8).
- Start pedalling.

11_TROUBLESHOOTING

The cadence value is not accurate:
the algorithm that calculates cadence without a sensor can
sometimes vary in accuracy. This might happen when
training with a high pedaling cadence at a low resistance
level.
If the hometrainer does not connect to the app:
The hometrainer needs to be properly powered up to work
and it needs to connect to a device within 15 minutes,
otherwise it will automatically enter its energy saving
phase. Start pedaling or unplug it and plug it in again to
reactivate it, and then connect to a device within 15 minu-
tes.
12_ADVICE ON USING YOUR ARION DIGITAL
SMART B+
1) The rollers work best with tyre that has a smooth tread.
If using a mountain bike, to reduce noise and increase
stability change the tyre for one with a slick tread.
2) For beginners, position the rollers in an entrance hall, in
a doorway or near a stable object, in order to have a sup-
port while acquiring the necessary balance.
3) Make sure the Arion Digital Smart B+ rests on a flat,
NOTES