Publicidad
Idiomas disponibles
Idiomas disponibles
•This tool should not be used by people under the age of 16 years
•If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous r
off the tool
•Use suitable detectors t
(contactwith electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion;
penetra
water pipe will cause property damage or an electrical shock)
•Hold the power tool only by the insulated gripping surfaces when performing an opera
theaccessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make
exposed metal parts of the power tool "live" and shock the operator)
•Dust from material such as paint containing lead, some wood species, minerals and metal may beharmful
(contact with or inhala
st may cause allergic r
operator or bystanders); wear a dust mask and work with a dust extr
•Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in
c
n
ves for wood c
device when connectable
•Follow the dust-related na
requirements for the materials you want to work with
•Do not work materials containing asbestos (asbestos is considered carcinogenic)
•If the cord is damaged or cut through while working, do not touch the cord, but immediately
disconnec
•Never use the tool when cord is damaged; have it replaced by a qualified person
•Always check that the supply voltage is the same as the voltage indicated on the nameplate of the
tool(tools with a ra
can also be connected to a 220V supply)
•Be aware of the forces that occur as a result of jamming (especially when drilling metals); always
useauxiliary handle and take a secure stance
•Always disconnect plug from power source before making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal
•If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not
le
a ended
SYMBOLS
Read the manual
Warning
Double isulation
Wear eye protection
OPERATING INSTRUCTION
ra
Before st
work, always examine the working area for concealed electric lines, gas and water pipes,
e.g. with a metal detector.
Always use the correct supply voltage! The voltage specifica
the supply voltage.
The power cord and plug must be in perfect c
4
atelyswitch
call the loc
company for assistance
/or respiratory diseases to the
evice when connectable
wear a dust mask and work with a dust extr
Wear ear protection
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
ra
ate must correspond with
GB
Working on the drill stand
Locking: Press ON/OFF switch 8 and lock with bu on 10.
Unlocking: Press ON/OFF switch 8 and release.
Speed control
(Fig.1)
The drilling speed can be adjusted during opera
OFF switch 8.
re
Speed control makes possible the slow st
slipping .the hole becoming enlarged or the material spli
tools
Clean and lightly grease tool shank befor
Twist the tool into the tool holder and push it in un
automa cally. Pull the tool to check if it is locked correctly.
Removing the tool
Push back the locking sleeve 2 of the tool holder and remove the tool.
P
ve and rever
switch on the switch to start drilling.
2. At end of the drilling opera
and rever
retreat from the drilled object.
Mode selector knob
The mode selector knob 7 may be set only when the machine is switched off.
Press the release bu on 6 on the mode selector knob 7 and move the knob to the desir
Drilling
Speed table
Applica on
Drilling
Wood/steel
Percussion drilling
Concrete/rock
Chisel adjustment
(Vario-lock)
Chiseling
Adjust and lock the chiseling angle:
If it is required to adjust the chiseling angle during chiseling
then, you can adjust the chiseling angle as per the chiseled object, at end of such adjustment, put back the
to "Picture, thus the chiseling angle will be locked.
material characterist
CLEANING AND MAINTANCE
Before any work on the machine itself, pull the mains plug.
For safe and proper working, always keep the machine and the ven a
Clean the tool mount daily.
If the machine should happen to fail despite the care taken in manufacture and tes
(Fig.1)
by increasing or decreasing the pressure on the ON/
st
gages. The tool shank lock
(Fig.6)
(Fig.2 )(Fig.3 )
ve and rever
on to "R" during drilling, the bit rotates right, then
a
on to "L", switch on the switch, the bit rotates le
Percussion drilling
Chisel adjustment
(Vario-lock)
Mode selector switch
(Fig.7 )
GB
.This prevents the drill from
ve
ay slowly
Chiseling
(Rota on OFF)
Speed control
SE/SER
to "Picture",
g, repair should be
5
Publicidad
