Installation; Chimney Connectors Requirements And Installation - Enerco H100 Instrucciones De Funcionamiento Y Manual Del Propietario

POSITIONING THE STOVE
When deciding on a location for the stove, choose
a location that will favor the most efficient heat
distribution possible throughout the house. Install the
stove in the room where the most time is spent and in
the most spacious room possible. A stove installed in
an open living room will have a higher efficiency than
one placed in a basement or outdoors in sub-freezing
temperatures. Burning dry wood will also make the
stove more efficient than burning wet wood.
When deciding on the position and orientation of the
stove be sure to obey all clearance to combustibles,
have the stove on smooth level floor and not raised up,
and if using the blower accessory have the stove within
65 inches (165 cm) distance of a 120v electrical supply.
WARNING: DO NOT INSTALL NEAR EXITS OR
STAIRS. ENSURE STOVE CAN NOT BLOCK AN
EVACUATION IN THE EVENT OF A FIRE.
CHIMNEY CONNECTORS REQUIREMENTS AND

INSTALLATION

If you have any questions regarding ventilation options
of your stove, contact either:
• The manufacturer Enerco Group Company at
251-0001. Our office hours are 8:00 AM – 5:00 PM,
EST, Monday through Friday.
• The National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 21 1 and NFPA Standard 908. The mailing
address of the NFPA is Battery March Park, Quincy,
MA 02269.
CAUTION: THIS STOVE SHALL NOT BE
INSTALLED IN A BEDROOM OR BATHROOM.
CAUTION: DO NOT INSTALL IN AN ALCOVE.
The chimney connector must be stove pipe meeting
these requirements:
• Have a 6 inch (152 mm) diameter
• Single wall
• Be made of 24 MSG (minimum standard gauge) blue
steel.
Insert the chimney pipe's crimped edge into the stove's
exhaust at the top of the stove. Secure the pipe in
place with three sheet metal screws through three
evenly spaced holes.
Any additional connector pipes or elbows should be
installed with crimped end on the stove end of the
Wood Fire Stove
path (not on the chimney end) and should be secured
with three evenly spaced sheet metal screws.
The following venting pipe precautions need to be
adhered to:
• At least 2 feet (61 cm) of vertical pipe coming out of
the stove is required, at minimum before the system
is permitted to have a horizontal section of venting.
• NOTE: Do not install the chimney directly at the outlet
of the appliance. A chimney connector (flue pipe) is
required unless the appliance is specifically approved
for that type of installation.
• Horizontal vent pipe must be sloped downward away
from the chimney 1/4" (0.6 cm) for every 1' (0.3m).
• Minimum clearance between the highest point of
horizontal vent pipe and the ceiling is 18" (45.7 cm)
• A total of two (2) elbows are permitted for venting
installation. Do not exceed two elbows as this may
result in inadequate draft and cause leakage of
smoke. When using elbows the integrity of the
draft can be best protected by using non adjustable
corrugated elbows.
CAUTION: THE JOINTS OF ANY AND ALL
CONNECTIONS FOR ANY VENTILATION
1-800-
SYSTEMS (COMBUSTION EXHAUST AND
OPTIONAL INLET AIR DUCT) MUST BE
SEALED WITH HIGH TEMPERATURE
SILICONE.
CAUTION: A CHIMNEY CONNECTOR SHALL
NOT PASS THROUGH AN ATTIC OR ROOF
SPACE, CLOSET OR SIMILAR CONCEALED
SPACE, OR A FLOOR, OR CEILING. WHERE
PASSAGE THROUGH A WALL, OR PARTITION
OF COMBUSTIBLE CONSTRUCTION IS
DESIRED, THE INSTALLATION SHALL
CONFORM TO CAN/CSA-B365, INSTALLATION
CODE FOR SOLID-FUEL-BURNING
APPLIANCES AND EQUIPMENT.
CAUTION: DO NOT CONNECT THIS UNIT
TO A CHIMNEY FLUE SERVING ANOTHER
APPLIANCE.
Where passage through a wall or partition of
combustible construction is desired, the installation
shall conform to chimney manufacturer's instructions.
NOTE: In Canada, installation must conform to
CAN/CSA-B365 when passing through combustible
construction, illustrated in Figure
E7
4 on next page.
Operating Instructions and Owner's Manual