Publicidad
Idiomas disponibles
Idiomas disponibles
• Place the work piece clamp (7) on the left or
right side of the machine.
• Hold the handgrip and move the saw slightly
downwards and then pull the pin (5) out slightly
so that saw moves upwards.
Note: Never use the mitre saw without the
extension pieces supplied. Make sure that they are
correctly mounted.
Sliding fence (Fig. B)
For safety reasons, this machine is equipped with a
moveable guide fence to used in normal and bevel
cutting.
• For normal straight cross-cuts and mitre cuts, al-
ways adjust the sliding fence (8) to the end and
fix well to provide safety support for work piece.
• For bevel cuts, adjust the sliding fence (8) to a
suitable position as close as to the saw blade
surface but avoid interfere the saw blade move-
ment and ensure to fix well.
Changing the saw blades (Fig. D and E)
Only use saw blades that are sharp and
undamaged. You must immediately replace
chipped or bent saw blades.
DANGER: Do not use any blade larger than the
stated capacity of the saw. It may come into contact
with the blade guard and cause harm.
Do not use a blade too thick to allow the outer blade
washer to engage with the flats on the spindle.
This will prevent the blade screw from securing the
blade on the spindle.
Do not use this saw to cut metal or masonry.
• Disconnect the machine from the power supply.
• Remove the screw (20) that holds the retraction
arm to the blade cover.
• Remove the screw (19) in order to remove the
bolt-cover by lifting the blade cover (6) upwards.
• Both saw blade bolt (17) and Flange (18) should
be visible now like shown in Fig. E.
• Press the saw blade lock button (22) Rotate the
saw blade carefully by hand until the blade locks.
• Use hex key to remove the saw blade bolt (17) by
loosening in a clockwise direction.
• Remove the Flange (18) and the saw blade.
• Replace the saw blade making sure that the arrow
marked on the saw blade must point in the same
direction as the arrow shown marked on the ma-
chine. The saw blade teeth must point downwards.
WWW.VONROC.COM
• Fix the saw blade bolt (17) use the saw blade
lock button (22) in order to secure tightly.
• Lower the blade cover (6) in order for the
bolt-cover to fall back into place and tighten the
screw (19).
• Attach the retraction arm back onto the blade
cover (6) by tightening the screw (20).
• Rotate the saw blade and check if the guard
operates freely.
Adjusting the cutting angle (Fig. A and B)
Adjusting Mitre Angles
The mitre angle can be set between 45° left side
and 45° right side.
• Loosen the locking knob (10).
• Press the locking paddle (11) and turn the saw ta-
ble left or right by the locking knob (10) until the
angle indicator (23) indicates the required angle.
• Release the locking paddle (11) and tighten the
locking knob (10).
Pre-settings (quick settings) on the following de-
grees: -45°, -30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°,
45°.
• Press the locking paddle (11) when turning the
baseplate, release the paddle before reaching the
requested degrees and the plate with "click" into
the pre-setting itself.
Adjusting Bevel Angles (Fig. A and C)
The bevel angle can be set between 0° and 45°.
• Loosen the adjusting knob (9).
• Tilt the saw by using the handle until the angle
indicator (14) indicates the required angle.
• Tighten the adjusting knob (9).
Changing the carbon brushes (Fig. B)
• Disconnect the machine from the power
supply.
• Unscrew the cover (4).
• Replace the carbon brushes with the exact
type of brushes.
• Tighten the cover (4) again.
Note: Always replace both carbon brushes at the
same time, never use a mixture of old and new
brushes.
Mounting the dust bag (Fig. A)
Press in the clamp of the dust bag (13) and slide it
onto the opening on the back of the machine. The
dust bag stays in place when you release the clamp.
EN
9
Publicidad
