Parkside PDS 120 B2 Instrucciones De Utilización Y De Seguridad página 37

• The safety, operating and maintenance information of the
manufacturer, as well as the dimensions specified in the
technical data, must be observed.
• The relevant accident prevention regulations and the other
generally accepted safety rules must be observed.
• The saw is only intended for installation indoors.
• Workpieces that are smaller than the saw blade guard can
cause injuries to the hands and fingers. Use a suitable aid!
• Avoid cramped hand positions when guiding the workpiece
and positions in which the hand would slip directly into the
saw blade.
• Always insert the saw blade so that the teeth point down
towards the saw table.
• Always set the correct blade tension in order to avoid
breaking the saw blades.
• Use extra care when cutting material with irregular cutting
profiles.
• When withdrawing the workpiece, teeth can get caught in
the kerf, especially if the shavings block the kerf. In this case
you should switch off the saw, pull out the mains plug, open
the kerf with a wedge and remove the workpiece.
• Never leave the work station without setting down the saw
beforehand. Wait until the saw has come to a standstill.
• Do not place, glue, or assemble any parts on the work table
while the saw is running.
• Do not switch on the saw until the work table is cleared of
material residues and tools. Only leave the workpiece to be
machined and any work aids (wedges) on the workbench.
• Always wear eye protection.
• Keep fingers at a safe distance from the saw blade.
• Guide the workpiece securely and firmly and do not let it
loose at any point.
• Never leave the work station without setting down the saw
beforehand.
• Do not let your familiarity with the saw lead you to
carelessness. Carelessness can lead to serious injuries in a
split second.
Keep these safety instructions in a safe place.
7. Technical data
Mains voltage .............................................220-240 V ~ /50 Hz
Power consumption ............................................. 80 watts (S1*)
............................................................... 120 watts (S6 30 %**)
Stroke rate ............................................................ 500-1700 rpm
Lifting movement ................................................................12 mm
Base .....................................................................630 x 295 mm
Tilting table ..................................................0° to 45° to the left
Table size .............................................................415 x 255 mm
Saw blade length approx. ............................................. 134 mm
Swing .............................................................................. 406 mm
Max. cutting height at 0° .................................................50 mm
Max. cutting height at 45° ..............................................22 mm
Min. size of workpiece W x H ............................. 100 x 22 mm
Max. size of workpiece W x H ............................ 400 x 50 mm
Protection category ...............................................................IP20
Weight ............................................................................. 13.2 kg
*Operating mode S1:
Continuous operation at constant load
32 GB/MT
**Operating mode S6 30%:
Continuous duty with intermittent loading (operating time 10
min.) In order avoid impermissible overheating of the motor,
the motor should be driven for only 30% of the operating time
with the stipulated nominal power and must then continue to
run with no load for the remaining 70% of the operating time.
Device emissions values
Noise
The noise levels have been determined in accordance with EN
61029.
Wear hearing protection.
Excessive noise can result in a loss of hearing.
Sound pressure level L ........................................... 66.9 dB(A)
pA
Uncertainty K ......................................................................3 dB
pA
Sound power level L .............................................. 79.9 dB(A)
WA
Uncertainty K .....................................................................3 dB
WA
The stipulated values are emission values and so do not
necessarily represent safe work station values. Although there is a
correlation between emission levels and exposure levels, it is not
possible to reliably determine whether additional precautionary
measures will be required or not based on this.
Factors that could influence the emissions level present at any
given time at the work station include the duration of exposure,
the nature of the working area, other noise sources etc. e.g. the
number of machines and neighbouring processes.
The permitted workstation values can also vary from country to
country. However, this information should enable the operator
to better evaluate the hazards and risks.
Limit the noise level to a minimum!
• Only use devices which are free of defects.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
Suitable saw blades
All industry-standard saw blades with a minimum length of 127
mm with and without a pin may be used.
8. Before commissioning
8.1 Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, keep the packaging until the expiry of the
warranty period.