Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

These instructions contain IMPORTANT safety information. Please read and keep for future reference.
The user must read and understand these Instruction Sheets and the Warranty.
Installation is the end user's responsibility and beyond Horizon Global's control. Therefore, Horizon Global exclusively limits its Warranty to
the repair or replacement of a defective product. Damage to your vehicle, your cargo or any person or property is excluded.
Your cargo basket must be inspected for signs of wear, corrosion and fatigue before each use. DO NOT use if bent or deformed.
Make sure your cargo basket is secure before every trip. Check at each stop to ensure your cargo basket is secure.
DO NOT exceed your cargo basket's weight capacity or your hitch tongue weight rating, whichever is lower. The capacity of your
cargo basket is 450 lb. (204 kg).
DO NOT attempt to drill, weld, or modify your cargo basket or any of the system components.
If cargo basket or cargo is in line with exhaust pipe, an exhaust tip must be used to redirect the exhaust flow away.
Position cargo so that the center of gravity is positioned in the middle third of the cargo basket.
DO NOT use your cargo basket for purposes other than those for which it was designed.
DO NOT use cargo basket to transport people, animals, or flammable liquids.
Check local and state laws governing projection of objects beyond the perimeter of a vehicle.
NEVER use elastic straps or belts to secure cargo.
ALWAYS obey all posted speed limits and be aware of traffic conditions. Adapt your speed to the conditions of the road and the load
being carried.
REDUCE YOUR SPEED. Your vehicle can handle differently when transporting cargo.
FREQUENTLY check your cargo basket and make sure the cargo is secure. Cargo can shift or your cargo basket can loosen during
travel. Readjust as needed. If movement continues, stop use.
When using your cargo basket to transport cargo, ALWAYS use caution when opening hatch to prevent damage to vehicle.
ALWAYS unload all objects before removing your cargo basket from hitch.
Remove your cargo basket when not in use and before entering automatic car washes.
The proper attachment of this product in accordance with the enclosed instructions is critical to its proper performance. See
instructions for proper attachment, proper usage, and important safety messages. Horizon Global has no control over, or responsibility
for, the attachment or the installation. Horizon Global is NOT responsible nor will it be held liable for any damage resulting from its
attachment or improper use. Horizon Global shall not be liable for any claims of any kind greater than the purchase price of the
product. Warranty information available upon request.
NOTICE: Your cargo basket will not prevent property damage that may result from improper loading, securing, or driving.
INSTRUCTION GUIDE FOR:
DART
CARGO BASKET
TM
59550 (2 inch hitch)
Date of Purchase:
WARNING
Review all Warnings, Instructions, and Warranty information carefully.
Failure to follow these warnings and instructions will void the Warranty.
For assistance with this product or to order replacement parts,
please contact:
Horizon Global, 47912 Halyard Drive Suite 100, Plymouth, MI 48170
(800) 234-6992
Or visit www.RolaProducts.com
PAGE 1
PAGE 1
59550_IN Rev B • Questions? (800) 234-6992 • RolaProducts.com
/
/

Publicidad

loading

Resumen de contenidos para Rola DART

  • Página 1 INSTRUCTION GUIDE FOR: DART CARGO BASKET 59550 (2 inch hitch) Date of Purchase: These instructions contain IMPORTANT safety information. Please read and keep for future reference. WARNING The user must read and understand these Instruction Sheets and the Warranty. Installation is the end user’s responsibility and beyond Horizon Global’s control. Therefore, Horizon Global exclusively limits its Warranty to the repair or replacement of a defective product.
  • Página 2 3. Attach center panel by using (4) self-tapping screws. FIG 2. 4. Note: the ROLA panel is attached to side with holes for light accessory kit (sold separately). 5. Insert bottom tabs of reflector in hole then push top tabs in until reflector snaps into place. Make sure the word “TOP” on the reflector is facing upwards.
  • Página 3 The handle side of the tilt assembly goes toward the tray side with ROLA panel. FIG 4. 2. Install (4) four 3/8 carriage bolts (from inside tray), flat washers and lock nuts as shown.
  • Página 4 INSTALLATION INSTRUCTIONS 5/8” Lock Anti-Rattle Pin Vehicle Mounting Washer 1. With the help of another person, install cargo basket into your 2” receiver hitch. 2. Line up threaded insert in shank with 5/8 hole in hitch and install the anti-rattle pin as shown in FIG 7. Clip 3.
  • Página 5 MODE D’EMPLOI POUR : PANIER À FRET DART 59550 (attelage de 5,08 cm [2 po]) Date d’achat : Ces instructions contiennent des consignes de sécurité IMPORTANTES. Lisez-les et conservez-les pour référence future. MISE EN GARDE L’utilisateur doit lire et comprendre ces fiches d’instructions et la garantie.
  • Página 6 3. Fixez le panneau central en utilisant (4) vis auto-taraudeuses. FIG. 2. 4. Remarque : le panneau ROLA est fixé sur le côté avec des trous pour la trousse d’accessoires d’éclairage (vendue séparément). 5. Insérez les onglets inférieurs du réflecteur dans le trou, puis poussez sur les onglets supérieurs jusqu’à ce que le réflecteur s’enclenche.
  • Página 7 Le côté de la poignée du dispositif d’inclinaison va vers le côté du plateau avec le panneau ROLA. FIG. 4. 2. Installez (4) quatre boulons de carrosserie 3/8 po (à l’intérieur du plateau), les rondelles plates et les écrous de blocage, comme indiqué.
  • Página 8 INSTRUCTIONS D’INSTALLATION Goupille Rondelle de Montage au véhicule anti-vibration blocage 5/8 po 1. Avec l’aide d’une autre personne, installez le panier à fret dans l’attache d’attelage de 2 po. 2. Alignez la douille filetée dans la tige avec un trou de 5/8 po dans l’attelage et installez la goupille anti-vibration comme indiqué...
  • Página 9 GUÍA DE INSTRUCCIONES PARA: CANASTA DE CARGA DART 59550 (gancho de 2 pulgadas) Fecha de compra: Estas Instrucciones contienen información IMPORTANTE de seguridad. Por favor, lea y conserve esta información para referencia futura. ADVERTENCIA El usuario debe leer y entender estos Instructivos y la garantía.
  • Página 10 3. Coloque el panel central utilizando cuatro (4) tornillos autorroscantes FIG 2. 4. Nota: el panel ROLA está colocado a lado con orificios para un kit de accesorio ligero (se vende por separado). 5. Inserte las pestañas del reflector en el orificio y luego empuje las pestañas superiores hasta que el reflector se inserte en su lugar.
  • Página 11 El lado de la manija del ensamble de inclinación va hacia el lado de la bandeja con el panel ROLA. FIG 4. 2. Instale cuatro (4) tornillos de transporte de 3/8 (desde la bandeja interna), las arandelas planas y las tuercas de seguridad como se muestra.
  • Página 12 INSTRUCCIONES DE INSTALACIÓN Montaje de vehículo Pasador Arandela de antivibración seguridad de 1. Con ayuda de otra persona, instale la canasta de carga en el receptor 5/8" de enganche de 2". 2. Alinee la inserción roscada de la pata con el orificio de 5/8 en el enganche e instale el pasador antivibración como se muestra en la FIG 7.

Este manual también es adecuado para:

59550