EINHELL FREELEXO SMART Manual De Instrucciones página 43

Version B:
1. Connect an empty USB stick to the USB con-
nection (24) as shown (Fig. 11).
2. Switch on the main switch (7) (ON).
3. The robot lawn mower will automatically save
the PUK to your USB stick and will then end
the operation with a beep.
4. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK, a personal
code. Please contact the customer services
team to obtain your PIN.
6.5 Settings of the robot lawn mower
The main menu on the LCD (50) shows you the
current date and time settings of the robot lawn
mower, as well as the current charge level. At the
same time the status of the rain sensor and of the
wire signal and of the selected mowing program
will appear in the toolbar. On the control panel
you can use either the "SET" button (51) to make
settings on the robot lawn mower or the "MODE"
button (52) to start the robot lawn mower with
various mowing programs. Use the navigation
buttons (55) to go to the option where you want to
make the settings. Press the "BACK" button (54)
in order to exit the respective menu.
Making settings with the "SET" button (51)
The "SET" button (51) can be used to make the
basic settings on your robot lawn mower. Use
the navigation buttons (55) to move to where you
want to go and then use the "OK" button (56) to
confi rm or the "Back" button (54) to discard the
settings you have made.
•
Zone
Where gardens have lots of angles, the robot
lawn mower may have problems reaching
every part of the lawn and mowing it comple-
tely. In this case you can select several star-
ting points on the perimeter wire (18). This will
enable the robot lawn mower to get to even
those parts of your garden that are difficult to
reach. The robot lawn mower will run the se-
lected distance along the perimeter wire (18)
and then start mowing in this part of the gar-
den (Fig. 6m). Use the navigation buttons (55)
to go to the point that you wish to change and
enter the distance and frequency accordingly.
The charging station (19) is automatically
defined as starting point 1. The two other st-
arting points can be selected as you wish. For
this you must measure the distance between
the charging station (19) and the starting
Anl_FREELEXO_SMART_SPK13.indb 43 Anl_FREELEXO_SMART_SPK13.indb 43
GB
point in clockwise direction along the perime-
ter wire (18). With the frequency setting you
decide how often the robot lawn mower starts
its work from the charging station (19) or from
the respective starting points.
•
Boundary cut
Once a week the robot lawn mower will mow
the edge of the lawn at the beginning of its
work window before it starts the mowing ope-
ration. The default factory setting is "On".
•
Error log
From here you will be informed about the
latest error messages concerning your robot
lawn mower.
•
Rain sensor
The rain sensor (5) can be switched on and
off with this setting. The default factory setting
for this sensor is "On". A detailed description
of the rain sensor can be found in the section
"Starting up" under "Sensors".
•
General
- PIN code: You can replace the default
PIN for the robot lawn mower with your own
choice of PIN. To do so, proceed as described
in the chapter "Locking mechanism / PIN".
Important! Make a note of the new PIN.
- Date & time: Use the navigation buttons
(55) to go to the point that you want to change
and make the settings accordingly.
- Language: Use the navigation buttons (55)
to activate the language that you want.
- Software version: The current version of
the robot lawn mower software is noted here.
•
Factory settings: Reset the robot lawn mo-
wer to the as-delivered state.
Mowing programs – "MODE" button (52)
Use the navigation buttons (55) to go to the mo-
wing program that you want to start.
•
Manual
In manual mode you can start the robot lawn
mower once with a different mowing program.
You can always choose between "Main area"
and "Secondary area". More details of the
two areas can be found in the section "Before
using for the first time" under "Perimeter wire".
- Mowing
When you start the robot lawn mower to mow
the lawn, the mower will switch to normal ope-
rating mode with the set time schedule.
- Boundary cut
Place the robot lawn mower close to the peri-
meter wire (18) or start the mower while it is in
the charging station (19). With its mower unit
activated, the robot lawn mower will follow
- 43 -
10.10.2022 12:44:18 10.10.2022 12:44:18