Publicidad
Garantía
1. Ultrasonic principle
Ultrasonic cleaning is on based on the cavitation effect caused
by high frequency ultrasonic wave vibration signal in the fluid.
Microscopic bubbles are formed, and they implode violently
causing the cavitation which create an intense scrubbing
action on the surface of the item being cleaned. The bubbles
are small enough to penetrate microscopic crevices, cleaning
them thoroughly and consistently.
Ultrasonic cleaning is extremely effective at removing dirt
and grime which would normally require tedious manual
cleaning by hand. It has been used to clean a wide variety
of instruments and mechanical parts such as carburetors,
returning them to almost "like new" condition without damage
to delicate parts.
2. Preparation
1.
Carefully unpack the cleaner and remove all traces of packing materials from it. Visually inspect
the cleaner for any parts that may have become loose or damaged during transit.
2.
Place the ultrasound on a clean, flat surface where the equipment receives adequate ventilation
and ensure all controls are turned off. Also ensure the drain tap is in the closed position (in the
references that include it).
3.
Ensure the power lead is securely plugged into the cleaner and that no part of the lead is likely
to come into contact with moisture.
4.
Carefully fill at least 1/2 of the tank with a solvent solution. For demanding cleaning we
recommend a small amount of washing up liquid, this will help increase the cleaning
performance. The cleaner is now ready for use.
Content
a: Main machine
c: Power lead
e: Manual
While the machine is working normally, the ultrasound and tank tuning gives a well graded
sound, and no tremors on the water surface. If there are discontinuous waves, please add
or release some washing solution in the tank; stopping waves is better for cleaning objects.
On the condition of making sure the object is cleaned, please run the machine discontinuously
as far as possible (no more than 30 minutes), long-time operation will cause the temperature
of the casing.
User's manual from ZCC016 to ZCC022
ENGLISH
b: Soundproof lid.
d: Mesh basket
Page. 12
Version 1, October 2022
6.2. For better cleaning effect
•
The item should be immersed well into the water (do not exceed the "MAX" mark)
•
Warm water (never hot or boiling) and a small amount of washing up liquid will help increase
the cleaning performance.
•
Make sure there is good space around each part you put in the tank,The more items that you place
in the tank the less efficiently it will clean. It is not advised to overlap items, If lay items one on
top of the other the system doesn't work the way it's supposed to.
•
Basket use. Do not put items directly into the bottom of the tank, better cleaning effect with a
suitable basket. A metal basket absorbs less ultrasonic energy at about 8%.
•
Temperature: The higher temperature the better cleaning effect. However, when temperature
exceed 70ºC ~ 80ºC, cleaning effect will be affect. The best temperature we suggest is 40ºC ~
60ºC.
7. General specifications
Power supply:
220VAC 50Hz
Temperature range:
0-80ºC (from ambient temperature to 80ºC) 1ºC in 1ºC selection
Time range:
1 – 99 minutes; selection from 1 in 1 minute
Display
LED, two four-digit LEDs (red colour)
Code
Frequency
Capacity
Drainage Tank size
(Hz)
(L)
tap
LxWxH (mm)
ZCC016
40
2
No
150x135x100
ZCC017
40
3.2
No
240x135x100
ZCC019
40
6.5
Yes
300x150x150
ZCC020
40
10
Yes
300x240x150
ZCC021
40
15
Yes
330x300x150
ZCC018
40
22
Yes
500X300X150
ZCC022
40
30
Yes
500x300x200
User's manual from ZCC016 to ZCC022
ENGLISH
Unit size
Heating
Ultrasonic Timer
LxWxH (mm)
power (W) power (W) (min)
175x160x210
100
60
1-99
265x165x220
100
120
1-99
325x180x280
300
180
1-99
325x265x280
300
240
1-99
360x325x285
400
360
1-99
550X330X280
500
480
1-99
530x325x325
500
600
1-99
Page. 17
Version 1, October 2022
Temp
(ºC)
RT-80
RT-80
RT-80
RT-80
RT-80
RT-80
RT-80
Publicidad
