Mixdown - Yamaha MT400 Manual De Instrucciones

20

Mixdown

After you have recorded all tracks, you are ready to mix them into a stereo mix, which you will
record to a stereo master recorder.
0
7
2
Connecting a master recorder
1
Connect the STEREO OUT jacks on the rear
panel of the MT400 to the input jacks of a
master recorder, and connect the output
jacks of the master recorder to the STEREO
INPUT 5L/6R jacks on the top panel of the
MT400.
Sending the tape playback sound to the
input channels
2
Set the [INPUT-FLIP] switches on Input
Channels 1–4 to "TAPE (
When the [INPUT-FLIP] switches are set to "TAPE
( )", the playback sound of the corresponding tracks
—Owner's Manual
POWER DC 12V
ON/ OFF
4
3
1 2 3 4
GAIN GAIN GAIN GAIN
LINE MIC LINE MIC LINE MIC LINE MIC
HIGH HIGH HIGH HIGH
–12 +12 –12 +12 –12 +12 –12 +12
MID MID MID MID
–12 +12 –12 +12 –12 +12 –12 +12
LOW LOW LOW LOW
–12 +12 –12 +12 –12 +12 –12 +12
AUX AUX AUX AUX
1 1 1 1
0 10 0 10 0 10 0 10
AUX AUX AUX AUX
2 2 2 2
0 10 0 10 0 10 0 10
MIX CUE MIX CUE MIX CUE MIX CUE
0 10 0 10 0 10 0 10
MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE MIC/LINE TAPE
to L to R to L to R
MIC/ MIC/ MIC/ MIC/
TAPE LINE TAPE LINE TAPE LINE TAPE LINE
INPUT-FLIP INPUT-FLIP INPUT-FLIP INPUT-FLIP
PAN PAN PAN PAN
L R L R L R L R
10 10 10 10
9 9 9 9
8 8 8 8
7 7 7 7
6 6 6 6
5 5 5 5
4 4 4 4
3 3 3 3
2 2 2 2
1 1 1 1
0 0 0 0
)".
SYNC OUT MONITOR OUT
R L
1
STEREO INPUT
5 6 7 8
L R L R
1 2
5 –6 7 –8
L R L R
LEVEL LEVEL
+6
+3
0 10 0 10
0
–5
–10
REC
MULTITRACK CASSETTE RECORDER
1 2
L R
TAPE SPEED CONTROL REC SELECT
PITCH
1 2 3
OFF OFF OFF
L R L
4.8/ 9.5
– +
ZERO STOP
ON ON
OFF OFF
SYNC
NOISE REDUCTION SYSTEM
MONITOR/PHONES
LEVEL
STEREO
ST+CUE
CUE
MIN MAX
STEREO
10
9
8
7
6
5
4
3
2
1
0 REC PLAY REW
5 6
are sent to the input channels, where you can adjust
tonal quality with the EQ controls and stereo position
with the PAN control. The playback sound sent to
Input Channels 1–4 are routed to the STEREO bus for
stereo mix and output from the SETEREO OUT jacks.
3
Set the monitor select switch to "STEREO".
The stereo bus is selected as a monitoring source, and
you can listen to the STEREO OUT signals via
headphones or an audio system connected to the
PHONES or MONITOR OUT jacks.
4
Set the [METER SELECT] switch to "STEREO".
The level meters L and R on the left indicate the level
of the Stereo bus signal output from the STEREO
OUT jacks.
STEREO OUT
R L
1
+6
POWER
+3
0
–5
–10
3 4
METER SELECT
4
4 4TR
OFF STEREO
R
3
FF STOP PAUSE