Steady Shot - Sony BRC-H900 Manual De Instrucciones

DISPLAY INFO (information display)
When the camera settings are stored in POSITION 1 to
16 using the supplied Remote Commander or the RM-
BR300 Remote Control Unit, the message "PRESET
No. xx" automatically appears for two seconds on the
monitor screen. If you want to display the message each
time the camera is operated, set DISPLAY INFO to ON.
Set it to OFF to cancel the display.
Note
The message will appear if the built-in cooling fan of the
camera has accidentally stopped. When DISPLAY
INFO is set to OFF, the display of this message is also
canceled.
SYNC MASTER
When you connect a sync signal generator, you can
select an output video signal that is synchronized with
the external video sync signal input to the EXT SYNC
IN connector on the camera.
When connecting the BRU-SF10 HD Optical Multiplex
Unit, select an output video signal that is synchronized
with the external video sync signal input to the EXT
SYNC IN connector on the BRU-SF10 HD Optical
Multiplex Unit.
HD: Selects the output signal from the
COMPONENT connector.
SD: Selects the output signal from the
S VIDEO connector.
When outputting from the SDI connector, select "HD"
for HD-SDI signal, or "SD" for SD-SDI signal.
H PHASE
When you connect a sync signal generator, adjust the
phase difference between the external video sync signal
input to the EXT SYNC IN connector on the camera and
video signal of the camera. The adjustable range is from
0 to 959 STEP.
The video signal advances for + setting, delays for –
setting from the external video sync signal.
Adjust following items.
HPHASE: Adjusts in 10 STEP (about 0.1347
The adjustable range is 00 to 95.
HPHASE FINE: Adjusts in 1 STEP (about 0.01347
μ
sec).
The adjustable range is 0 to 9.
When you set more than 9, the HPHASE value
increases 1 and HPHASE FINE value returns to 0
automatically.
When you set to less than 0, the HPHASE value
decreases in 1 and HPHASE FINE value returns to
9 automatically.
Note
HPHASE and HPHASE FINE does not appear when a
BRU-SF10 HD Optical Multiplex Unit is in use.

STEADY SHOT

You can select the effects of picture blur compensation
depending on shooting conditions.
OFF: Disables the picture blur compensation.
ON: The picture blur compensation is activated.
Notes
• This function does not work while the camera is
panning or tilting. After panning or tilting is stopped,
it may take some time to stabilize the picture.
• It may take some time to obtain stable images after
turning on the camera when STEADY SHOT is
activated.
• Picture blur compensation may not work depending
on installation conditions.
COLOR BAR
When this item is set to ON, the built-in color bar of the
camera is displayed on the monitor screen.
RGB/
TALLY MODE
VIDEO or
Adjusts setting of the tally lamp on the front and back on
the camera. Select from HIGH, LOW, or OFF.
HIGH: Makes the front tally lamp bright when the tally
lamp is turned on.
LOW: Makes the front tally lamp dim when the tally
lamp is turned on.
OFF: Both the front and back tally lamps are not turned
on even if the ON command for the tally lamp is
received.
Note
When the TALLY MODE is set to OFF, both the front
and back tally lamp are not turned on.
You cannot adjust the brightness of the back tally lamp.
μ
sec).
The brightness of the back tally lamp is same for the
HIGH or LOW setting.
PRESET MODE (Preset mode)
You can select the items to be stored in the PRESET.
MODE1: Stores the positions of the pan/tilt/zoom and
the setting items
MODE2: Stores the positions of the pan/tilt/zoom and
the focus position (only when set to MANUAL
mode).
1)
For details of the camera settings to be preset, see
"Presetting Items" on page 79.
1)
of the camera at the same time.
SYSTEM Menu
41
GB