Functional Description - Milwaukee 9070-20 Manual Del Operador

1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
2. Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replace-
ment.
3. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
Symbology
Double Insulated
Volts Alternating Current/
Direct Current
Volts Alternating Current
Amperes
Impacts per Minute
Under Load (IPM)
Underwriters
Laboratories, Inc.
Canadian
Standards Association
Mexican Approvals Marking
1. Drive shank
2. Forward/reverse switch (Cat. No. 9072-20, 9092-20 and 9096-20)
3. Trigger (Cat. No. 9072-20, 9092-20 and 9096-20)
Rocker switch (Cat. No. 9070-20, 9071-20, 9075-20)
4. Speed control dial (Cat. No. 9072-20, 9092-20 and 9096-20)
5. Quik-Lok ® cord(Cat. No. 9072-20, 9092-20 and 9096-20)
6. Quick change chuck (Cat. No. 9092-20 and 9096-20)
7. Tool hanger (Cat. No. 9092-20 and 9096-20)
8. Tool hanger ring (Cat. No. 9092-20 and 9096-20)
3
Cat. No. 9075-20
SPECIFIC SAFETY RULES - IMPACT WRENCH
Cat.
No.
9070-20 120 AC/DC
9071-20 120 AC/DC
9072-20 120 AC Only
120 AC/DC
9075-20
120 AC Only
9092-20
120 AC Only
9096-20
Quick Change Chuck Capacities*
Cat. No.
9070-20
9072-20
9092-20
9096-20
* Only for use with the 7/16" or 5/8" Hex Quick Change chuck,
standard equiptment on the 9092-20 (7/16") and 9096-20 (5/8"),
optional accessory (Cat. No. 48-66-0061) on other models.

FUNCTIONAL DESCRIPTION

1
6
Cat. No. 9092-20
Specifications
No Load
A
Volts RPM
7 1800
7 1800
7 600-1800
7 1750
7 600-1800
7
600-1800
Quick Change Auger Bits
1-1/2"
1-1/2"
1-1/2"
1-1/2"
2
3
4
8
7
Average
Drive
Impacts Per
Torque Output
Shank
Minute
1/2" 2600 300 ft-lbs.
1/2" 2600 300 ft-lbs.
1/2" 1000-2600 100-300 ft-lbs.
3/4" 2500 380 ft-lbs.
7/16" Hex 1000-2600 100-315 ft-lbs.
5/8" Hex
1000-2600 100-315 ft-lbs.
Selfeed Bits
2-9/16"
2-9/16"
2-9/16"
2-9/16"
Cat. No. 9072-20
5
page 3