Narex EPR 350-24 Instrucciones De Uso Originales página 22

English
5 Technical Specification
The devices are manufactured in accordance with EN 50144‑2‑13 and conform fully to the wording of the act on safety of devices and products.
Type
Rated voltage (V)
Rated frequency (Hz)
Power input (W)
Current (A)
Engine speed (min )
‑1
Guide bar – length (mm)
Chain
Chain pitch
Chain gauge (mm)
Chain speed (m/s )
‑1
Chain brake
Runout brake
Chain lubrication
Oil tank volume (ml)
Chain tensioning system
Class of protection
Weight (without bar) (kg)
Weight (with bar) (kg)
6 Machine Description
[1] .......Oil level gauge
[2] .......Front handle
[3] .......Oil tank cap
[4] .......Front hand guard (chain brake trigger)
[5] .......Guide bar
[6] .......Saw chain
[7] .......Manual clamping nut
[8] .......Sprocket wheel cover
[8a] .....Catch
[8b] .....Lock‑in hole
[9] .......Switch
[10] .....Rear hand guard
[11] .....Rear handle
[12] .....Arched handle
[13] .....Lock‑out switch
[14] .....Chain catcher
[15] .....Power cable with plug
[16] .....Lead‑in (extension) cable
[17] .....Hole for cable loop
[18] .....Hook for cable loop
[19] .....Chain drive wheel (sprocket)
[20] .....Grooved wheel for chain tensioning
[21] .....Chain tensioning pin
[22] .....Air holes
[23] .....Scabbard
7 Double insulation
To ensure maximum safety of the user, our tools are designed and built
to satisfy applicable European standards (EN standards). Tools with
double insulation are marked by the international symbol of a double
square. These tools must not be grounded and a two‑wire cable is suffi‑
cient to supply them with power. Tools are shielded in accordance with
EN 55014.
8. Use
Attention! This chainsaw is intended for cutting wood only!
22
EPR 350-24
230
50
2 400
11
7 000
350
OREGON 91‑PX 053X
3/8"
1.3
ca 14
mechanic
mechanic
automatic
210
FastFix
II /
4.5
5.1
9 Putting into operation
Check whether the data on the rating plate conform to the real volt‑
age of the power supply source. Check whether the plug type conforms
to the socket. The device intended for 240 V can be also connected to
220 / 240 V.
9.1 Oil tank filling
The chainsaw may never work without the oil, because lack of oil can
lead to damage of the chain, bar and engine. Damage as the conse‑
quence of work without oil is not covered by the warranty.
Attention!
Be so kind and use only the oil suitable for the
saw chains.
Bio oil NAREX CO 1l (ord. no. 65403576) can be purchased in specialised
shops. Do not use any worn out oil. Doing so would damage your chain‑
saw and void the warranty.
» Before refilling the oil tank, first unplug the cord from the power
source.
» Unscrew the cap [3]. The cap is fitted from the inside with a plastic
tether with a retainer to prevent the loss of the cap.
» Use a funnel to pour approximately 210 ml of oil into the tank and
firmly screw the cap back on.
» The oil level can be seen through the level gauge [1].
» Empty the oil tank before transporting the chainsaw!
» Check that the chain lubrication system is functional before you
begin work. Turn the chainsaw on when the cutting mechanism
EPR 400-24
230
50
2 400
11
7 000
400
OREGON 91‑PX 057X
3/8"
1.3
ca 14
mechanic
mechanic
automatic
210
FastFix
II /
4.5
5.2