Craftsman 2600 MAX PSI Guía Rápida De Inicio

WARNING Failure to read and follow the operator's
manual and all operating instructions can
result in death, bodily injury, and/or property
damage.
WARNING Fuel and its vapors are flammable and
explosive. Turn off engine and wait at least
2 minutes before refueling. Let spilled fuel
evaporate before starting engine. Always allow
space for fuel expansion.
WARNING High pressure water spray can cut
through skin. Never spray people or animals,
as injury can result. Spray gun traps high
water pressure, even when engine is stopped
and water is disconnected. ALWAYS point spray gun in
safe direction, press red button and squeeze spray gun
trigger, to release high pressure, every time you stop
engine.
You will need:
• Utility knife • Unleaded fuel • Garden hose, 50 feet (15 m) or less • Safety goggles (indirect vented type)
Unpack Pressure Washer
1. Remove everything from carton except pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly. If items are
damaged or missing, call 1-800-222-3136.
4. Prior to assembly, lubricate all o-ring connections as described in
operators manual.
Assemble Pressure Washer
1. Place handle (A) onto handle supports connected to main unit.
Make sure holes in handle align with holes on handle supports.
2. Insert handle carriage bolts (B) through holes from inside of unit
and attach a plastic knob (C) from outside of unit. Tighten by
hand. 1
NOTICE By loosening both knobs to the middle section of the
attachment bolt, the upper handle can fold forward to store flat atop the
cold engine. DO NOT fold the handle down while the engine is hot.
3. Insert rubber straps (D) through slots (E) in back of accessory tray
and pull tight from front.
2
4. Place accessory tray (F) over holes (G) on handle (viewing from
front of unit). Push the tree clips (H) into the holes until they sit flat
against the accessory tray. 3
5. Insert multi–colored quick connect spray tips and other supplied
accessories in spaces provided in accessory tray. See How to Use
Accessory Tray, in operator's manual.
6. Attach bottle bracket (J) to handle with carriage bolt (K) and black
plastic knob (L). Tighten by hand.
4
Attach PerfectMix™ Siphon to Pump
and Concentrate Bottle
1. Place PerfectMix™ bottle (P) (not included) in wire-form bracket on
handle. Remove cap from bottle and insert PerfectMix™ Siphon (M).
Screw siphon unit to top of bottle. Use clip on cap (Q) to snap siphon
to wire form bracket when siphon is not in a concentrate bottle.
2. Attach tube end of blue PerfectMix™ Siphon (R) to barbed tube
fitting (S) on pump.
6
© 2011 Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).
Quick Start Guide
2600 MAX PSI* Pressure Washer
WARNING Outdoor use ONLY. DO NOT start or
run engine indoors or in an enclosed area,
even if windows and doors are open.
Running engines give off carbon monoxide,
an odorless, poison gas that can cause
nausea, fainting or death.
WARNING Starter cord kickback (rapid retraction)
can result in bodily injury. NEVER pull
starter cord without first relieving spray
gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Kickback will pull
hand and arm toward engine faster than you can let go.
High pressure can cause spray gun to kickback. Hold
spray gun with both hands during use.
WARNING Risk of eye injury. Spray can splash
back or propel objects. Always wear indirect
vented (chemical splash) safety goggles,
marked to comply with ANSI Z87.1 when
using or in vicinity of this equipment. NEVER substitute
safety glasses or dry-condition goggles for indirect
vented safety goggles.
Operator's Manual and Standard
Items Included:
Siphon Hose (not shown)
1
B
A
C
2
1
E D
3
H
4
K
J
5
5
M
P
6
R
S
Add Engine Oil and Fuel
NOTICE Before starting the engine, check oil level and ensure that
engine is serviced as described in the Operator's Manual.
NOTICE DO NOT use E85 fuel.
NOTICE DO NOT mix oil with fuel.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove oil fill cap/dipstick (
3. Using oil funnel (optional), slowly pour entire contents of oil bottle
into oil fill.
4. Replace and fully tighten oil fill cap/dipstick.
5. Clean area around the fuel cap (
6. Slowly add regular unleaded fuel to bottom of fuel level limit in neck
of fuel tank. Be careful not to overfill.
7. Replace fuel cap. Let any spilled fuel evaporate before starting
engine.
Move Pressure Washer
to Safe Operating Location
1. Move pressure washer outdoors to a flat, level surface.
WARNING Running engine gives off carbon monoxide, an
odorless, colorless, poison gas. Breathing carbon
monoxide could result in death, serious injury, nausea or
fainting. Operate this product ONLY outdoors. DO NOT
operate this product inside any building or enclosure, even if windows
and doors are open.
2. Running engines give off carbon monoxide. Keep at least 5 ft.
(1.5 m) clearance on all sides of pressure washer including overhead
to reduce the risk of exhaust heat or exhaust gases igniting nearby
combustible material.
8
Connect Spray Gun
NOTICE Remove and discard 2 shipping caps from high pressure outlet
and garden hose inlet connections.
1. Uncoil high pressure hose (T) and attach one end of hose to base of
spray gun (U). Tighten by hand.
2. Attach other end of high pressure hose (T) to high pressure outlet
(V) on pump. Tighten by hand.
Connect Water Supply
NOTICE DO NOT use pressure washer if inlet screen is damaged or
missing, call 1-800-222-3136.
1. Inspect garden hose inlet screen (W) for damage.
2. Clean screen if it contains debris or have it replaced if damaged.
3. Run cold water through garden hose for 30 seconds to clean out any
debris. Connect garden hose (X) (not to exceed 50 feet in length) to
water inlet (Y). Tighten by hand.
Start Pressure Washer
NOTICE You MUST connect and turn on water supply fully before
starting engine.
1. Put on safety goggles.
WARNING Risk of eye injury. Spray could splash back or propel
objects resulting in serious injury. Always wear indirect
vented (chemical splash) safety goggles marked to
comply with ANSI Z87.1 when using or in vicinity of this
equipment. NEVER substitute safety glasses or dry-condition goggles
C
for indirect vented safety goggles.
2. Turn on water supply.
3. Press red button (Z) on spray gun and pull trigger until water comes
out in a steady stream. Release trigger to locked position.
4. Attach nozzle extension (AA) to spray gun (U).
5. Pull back on collar of nozzle extension (BB), insert spray tip (CC) and
release collar. Tug on spray tip to make sure it is securely in place.
6. Turn fuel valve to "On" position.
7. Pull choke rod to "Closed" position.
8. Move engine switch to "On" position.
9. When starting engine, position yourself as recommended and grasp
starter grip handle and pull slowly until you feel some resistance.
Then pull rapidly to start engine.
10. Return starter grip handle slowly. DO NOT let rope "snap back"
F
against starter.
WARNING Starter cord kickback (rapid retraction) will pull hand
G
and arm toward engine faster than you can let go which
could cause broken bones, fractures, bruises, or sprains
resulting in serious injury. NEVER pull starter cord without
first relieving spray gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Firmly grasp spray gun with both
hands when using high pressure spray to avoid injury when spray gun
kicks back.
11. After each starting attempt, where engine fails to run, always point
gun in safe direction, press red button and squeeze spray gun trigger
L
to release high pressure.
12. When engine starts, slowly move choke rod to "Open" position
as engine warms. If engine falters, move choke rod to "Closed"
position, then to "Open" position.
13. Point gun toward surface to be cleaned. Push red button and pull
trigger to begin spraying.
Stop Pressure Washer
1. Let engine idle for 2 minutes.
Q
2. Move engine switch to "Off" position.
3. Turn off water supply.
4. Point spray gun in safe direction, press red button, and squeeze
spray gun trigger to relieve retained high water pressure.
NOTICE Spray gun traps high water pressure, even when engine is
stopped and water is disconnected.
5. Disconnect garden hose from pump.
6. Disconnect high pressure hose from pump and gun for storage. For
long term storage instructions, see operator's manual.
7. Remove safety goggles.
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-222-3136
Or visit our website www.craftsman.com
7
).
7
8
), remove fuel cap.
7
Exhaust Port
Pointed away from
dwelling openings
9
U
10
9
11
10
12
11
11
13
14
CC
15
12
13
14
15
16
16
17
16
17
16
For tips on how to
set up and use your
pressure washer,
scan this code with
your Smartphone
(data rates apply).
T
T
V
W
Y
X
Z
U
AA
BB
OFF
ON
Closed