Cordless tacker
Fasteners
Staple strip
– Width
– Length
Nail strip
– Length
Max. magazine capacity
Weight according to EPTA-
A)
Procedure 01:2014
Permitted ambient temper-
ature
– During charging
B)
– During operation
and
during storage
Recommended re-
chargeable batteries
Recommended battery
C)
chargers
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according
to EN 60745‑2‑16.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 84 dB(A); sound power
level 95 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2‑16:
2
2
a
< 2.8 m/s
, K = 1.5 m/s
.
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
Bosch Power Tools
power tool and application tools, keeping the hands warm,
UniversalTacker
and organising workflows correctly.
18V-14
Rechargeable battery
Type 53
Bosch sells some cordless power tools without a re-
mm
11.4
chargeable battery. You can tell whether a rechargeable bat-
mm
6–14
tery is included with the power tool by looking at the pack-
Type 48
aging.
mm
14
Charging the battery
140
u
kg
1.8 (1.5 Ah)–
2.1 (6.0 Ah)
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
°C
0 to +35
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
°C
–20 to +50
the first time.
PBA 18V...W-.
Inserting the Battery
Push the charged battery into the battery holder until it
AL 18...
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the remaining battery
capacity or an overload for a few seconds when the power
tool is switched on.
The battery charge indicator indicates the state of charge for
a few seconds when the on/off switch is half or fully pressed.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × slowly flashing green light
If the battery charge indicator flashes red, the power tool is
overloaded.
The three LEDs in the battery charge indicator flash quickly
when the temperature of the rechargeable battery is outside
the operating temperature range and/or the overload protec-
tion has been triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 6V3 | (09.09.2022)
English | 15
Capacity
75–100 %
40–75 %
15–40 %
0–15 %