Publicidad
Idiomas disponibles
Idiomas disponibles
EN
distributor.
Keep warning and information labels
always clean and legible.
Keep all nuts, bolts and screws tight so
that the machine can operate safely.
If any components or safety devices
are removed while maintenance works,
they must be reassembled properly.
2.7 - STORAGE In CASE Of
LOnGER STOPPInG PERIODS
Never store the tool with gasoline in the
tank inside a building. Gasoline steam
may come into contact with flames or
sparks and explode.
Store the unit in a dry area with the
fuel tank empty and the fuel in a
well-ventilated compartment. Avoid
places with high humidity to avoid the
appearance of corrosion and rust.
Clean the appliance thoroughly before
storage, especially in winter. Keep the
device in a good operating mode.
Make sure the device is protected
against unauthorized use (for example,
by children).
2.8 - TECHnICAL ASSISTAnCE
Your device must only be repaired
by the brand's technical service or
qualified professionals and only with
original spare parts.
3. ASSEMBLY
InSTRUCTIOnS
3.1 - ROTATIOn SHAfT
ASSEMBLY (fIG. B)
1. Untighten the fixing and tightening
screws of the rotating shaft flexible hose
(11) through the gearbox protection
holes (9);
2. Insert the A tip (10) of the flexible
40
hose on the supporting flange in the
gearbox. Simultaneously, fit the rotating
shaft in the gearbox shaft's hole;
3. Spin the rotating shaft flexible hose
so that the fixing hole gets aligned with
the gearbox fixing screw;
4. Tighten the fixing and tightening
screws and make sure the flexible hose
is well tightened;
5. Adjust the rubber protection of the
flexible hose fixation;
3.2 - ASSEMBLInG THE
COnTROL HAnDLE In THE
fLEXIBLE HOSE Of THE
ROTATInG SHAfT (fIG. C)
1. Untighten the fixing and tightening
screws of the rotating shaft flexible
hose through the gearbox protection
holes (13);
2. Insert the B tip (12) of the flexible
hose (11) in the control handle hole.
Simultaneously, insert the rotating shaft
of the flexible hose in the control handle
hole;
3. Tighten the control handle fixing
screw in the flexible hose;
3.3 - ASSEMBLInG THE
AUXILIARY HAnDLE In THE
ROTATInG SHAfT TUBE
(fIG. D)
1. Align the tightening ring hole (20)
with one of the three holes
rotating shaft's tube (5);
2. Fit the auxiliary handle lower rod
(19) in the tightening (16) ring and
match the holes;
3. Insert the auxiliary handle in the
tightening ring.
The arrow on the handle must be facing
away from the cutting accessories
holder and the pin on the handle fitting
must match the hole in the tightening
ring;
4. Insert the screw, washer and fixing
nut in the auxiliary handle holes and
tighten them clockwise;
3.4
-
ASSEMBLInG
CUTTInG
PROTECTIOn (fIG. E)
The cutting accessories protection (3)
avoids the projection of loose objects
and accidental contact with the user.
1. Adjust the fixing plate (17) in the
cutting accessories holder (18). Insert
the washers and tighten the fixing
screws;
2. Install the cutting accessories
protection on the fixing plate;
3. Insert the screw in the fixing plate
perforation and tighten it in the cutting
accessories protection;
4. Insert the flap (4) in the cutting
accessories protection base and fix it in
the fixing sockets;
5. Place and tighten the fixing screw;
The
protection does not protect the
user against all objects (stones, glass,
cables, etc.) that are projected for the
cutting accessory. These objects can
bounce off any surface and reach the
user.
3.5 - ASSEMBLInG THE
CUTTInG DISC (fIG. f)
of the
Check the disc status before installing
it. If damaged (fractured, bent or
cracked), replace it.
1. Place the supporting base (21)
in the rotating screw on the cutting
accessories holder (18)
2.Place the supporting base in the
sprocket wheel of the rotating screw;
3. Install the cutting disc (24) in the
supporting base. Assure that the disc
is installed with the blade pointing the
rotation movement;
THE
ACCESSORIES
cutting
accessories
Publicidad
