Aritech DD66X Serie Manual De Instalación página 5

mode for 30 minutes. The detector returns to normal operating
mode after the walk test mode times out.
During the walk test the installer should cross a curtain to
trigger the PIR, and change the distance from detector to
trigger the radar. The simplest method is to cross a selected
curtain, and then move towards the detector to activate a dual
alarm. See Figures 4 and 5 for the curtain floor pattern.
Next, the installer should wait 40 seconds before repeating the
walk test on the consecutive curtain of the detector pattern.
Note: An environment with a higher microwave noise may
require a longer quiescent time for radar circuits to stabilize.
Green mode (AM detectors only)
The detector can be programmed in several ways to minimize
the human and animal exposure to microwave radiation,
although the detector is already sending microwave signal on a
very low power level.
The detector will switch the microwave section off for 3 minutes
after a dual alarm. The detector is in PIR only during this timer.
Settings option 1 J1: Off
Settings option 2 J1: Removed
The microwave section is switched off and for DD66XAM is
switched to AM section. The detector operates in PIR mode
only.
Setting J1: Removed
LED indication
DD66X
Dual
Start up
Low voltage
(Dual) motion
intruder alarm
Latched PIR
(Memory)
DD66XAM
Dual / AM
Start up Closed
Low voltage Open
(Alarm)
(Dual) motion Open
intruder alarm (Alarm)
Latched PIR
(Memory)
Open
AM alarm
(Alarm) [2]
Technical fault
P/N 146249999-5 (ML) • REV J • ISS 27JUL21
System in Armed status
System in Disarmed status
System Walk Test Disabled
Closed Automatically after 45 s
Open Apply correct voltage
(Alarm)
Open Automatically after 3 s
(Alarm)
Switch to Night mode
Closed Automatically after
60 s
Open Apply correct voltage
(Alarm)
Automatically after 3 s
Switch to Night mode
Open
See DIP switch 7
(Alarm)
Open Pass walk test
(Alarm)
Continuously on Normal blinking (1 Hz)
[1] Tri-colour LED.
[2] Depends on the setting of the DIP switch SW8.
Specifications
DD669 DD666-D DD669AM
Detector
Range diameter
or 12 ±0.5 m (39 ft. 4 in. ±1 ft. 7 in.)
(selectable)
Viewing angle
(selectable)
Optical
Microwave
frequency
Maximum power
output
Max microwave
output at 1 m
Memory
Input power
Peak-to-peak ripple
Detector start-up
time
Normal current 12 mA
consumption
Current consumption 10 mA
in Alarm
Maximum current 15 mA
consumption
Mounting height 2.5 to 5.0 m (8 ft. 2 in. to 16 ft. 5 in.)
0.3 to
Target speed range
3.0 m/s
(1 ft./s
to 9 ft.
10 in./s)
Alarm (NC) / Tamper 80 mA
relay characteristic 30 VDC
Form A
Pry off tamper Optional
AM relay
characteristic
Alarm time
Operating
temperature
 138 x 92 mm ( 5.43 in. x 3.62 in.)
Dimensions ( x H)
Relative humidity
Weight
IP/IK rating
Regulatory information
Manufacturer PLACED ON THE MARKET BY:
Carrier Fire & Security Americas Corporation Inc.
13995 Pasteur Blvd
Palm Beach Gardens, FL 33418, USA
AUTHORIZED EU REPRESENTATIVE:
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
DD666AM-D
Dual Dual + AM
20 ±0.5 m (65 ft. 7 in. ±1 ft. 7 in.)
360 degrees or 180 degrees
2 x 9 curtains
5725 to 5875 MHz
3.89 W
0.003 μW/cm²
Yes
9 to 15 VDC (12 V nominal)
2 V (at 12 VDC)
45 s 60 s
19 mA
20 mA
25 mA
0.2 to 0.2 to 0.2 to 3.0 m/s
3.0 m/s 3.0 m/s (8 in./s to 9 ft.
(8 in./s to (8 in./s to
9 ft. 9 ft. 10 in./s)
10 in./s)
80 mA 80 mA
30 VDC 30 VDC
Form C Form A
On board (Yes)
N/A 80 mA at 30 VDC max.
3 s
−10 to +55°C (14 to 130°F)
max. 95%
255 g (9 oz.)
IP30 IK04 (indoor use only)
10 in./s)
80 mA
30 VDC
Form C
5 / 42