Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING: When battery charge runs
out after continuously use or
exposure to direct sunlight or heat, allow
time for the tool to cool down before re-
charging to achieve the full charge.
2. TO REMOVE OR INSTALL THE BATTERY
PACK (SEE FIG. B)
Depress the battery pack release button to release and
slide the battery pack out from your tool. After recharge,
slide it back into your tool. A simple push and slight
pressure will be sufficient.
ASSEMBLY
1. ASSEMBLE THE SANDING PAPER (SEE
FIG. C)
1)
Remove any dust or other objects from the sanding
plate and sandpaper.
2)
The sandpaper has dust extraction holes you must
align these with the holes in the sanding plate,
otherwise the dust extraction will not function.
2. FITTING AND REMOVING THE DUST BAG
(SEE FIG. D)
Attaching the dust bag
Your sander is equipped with a dust bag. To attach, slide
the dust bag onto the dust outlet at the rear of the sander.
CAUTION! To prevent the possibility of sanding
dust or foreign body being thrown in to your face or
eyes, never attempt to use your sander without the dust bag
properly installed.
EMPTY THE DUST BAG (SEE FIG. E1, E2)
For more efficient operation, empty the dust bag every
5-10mins.To empty the dust bag, first remove it from the
dust extraction outlet, and then you can shake the dust
out.
3. ATTACHING SANDER TO VACUUM (SEE
FIG. F)
Your sander is equipped with a vacuum adapter, which
is designed for collecting dust task. Insert the vacuum
adapter into the rear dust extraction outlet and ensure
it is tightened securely. Then connect the adapter to the
hose of a vacuum cleaner.
While using, first turn on the vacuum cleaner, and then
turn on the sander. If you stop sanding, first turn off the
sander, then turn off your vacuum cleaner.
NOTE: Please always connect the adaptor with 35mm
vacuum hose.
18
4. PLACE THE POLISHING PAD (SEE FIG.
G1, G2)
The machine is equipped with a polishing pad. Place the
polishing pad securely on the rotary plate and make sure
it's centrosymmetric. Otherwise the polisher vibrates badly.
OPERATION
1. Operating the ON / OFF SWITCH (SEE
FIG. H)
To start your sander, depress the protective cover over
the switch at the position marked "I".
To stop your sander, depress the protective cover at the
position marked "0".
2. VARIABLE SPEED CONTROL (SETTING
SPEED:1-5-MAX) (SEE FIG. I)
With the variable speed control, the required speed can
be selected (also while running).
The required speed is dependent on the material and is to
be determined by a practical trial.
3. HAND GRIP AREA (SEE FIG. J)
Your sander is designed to be held by the top of the main
housing.
4. USING THE SANDER
The workpiece to be sanded must be secured. If it is
small or it may move during sanding, it must be held in a
vice or suitably clamped.
Be sure to hold the sander firmly whilst it is turned on
and apply it gently to the work, it may "kick" on first
contact. Hold the sander so that it is flat on the work and
move slowly, preferably with a smooth, circular motion.
Regularly check the condition of the sanding paper and
replace when worn for best results.
Rough sanding
Attach a Sand paper with coarse grain. Apply only light
sanding pressure to achieve increased material removal.
Fine sanding
Attach a Sand paper with fine grain. With moderate
pressure, move the machine in a circular pattern or
alternately in lengthwise and crosswise directions over
the workpiece. Do not tilt the machine to avoid sanding
through the work piece (e.g. when sanding veneer). After
finishing the work, switch off the machine and lift it from
the workpiece.
EN
Publicidad
