Wesco WS2961 Manual De Instrucciones página 18

2) Slide the battery pack into the charger, the light
will turn to red to indicate the charging process has
started.
3) When charging is completed, the light will turn to
green. The pack is now fully charged, unplug the
charger and remove the battery pack.
NOTE: If the battery pack is locked in the charger, press
the battery pack release button and remove it.
WARNING: When battery charge runs
out after continuously use or exposure
to direct sunlight or heat, allow time for the
tool to cool down before re-charging to
achieve the full charge.
CHARGING INDICATOR
Light
ReRed ono
Green on
3. TO REMOVE OR INSTALL BATTERY PACK
(SEE FIG. E1, E2)
Depress the battery pack release button firmly first and
then slide the battery pack out from your tool.
After recharge, slide the battery pack into tool's battery
ort. A simple push and slight pressure will be sufficient.
4. POWER SUPPLY WITH CAR CIGARETTE
LIGHTER BY 3M 12V AUTO POWER
ADAPTER
Insert the 3m 12V auto power adapter into the car
cigarette lighter.
OPERATION
1. SELECTOR SWITCH FOR INFLATOR/
BLOWER MODE (SEE FIG. F)
Place this switch in the (I) position to turn on the High
pressure pump or the (II) position to turn on the low
pressure pump. Place the switch in the (O) or center
position to stop all pump operations.
2. DISPLAY SCREEN (SEE FIG. G)
The display screen shows digital gauge.
The digital gauge measures and displays the air pressure,
monitors pressure output, and is used to set pressure
type.
And the display screen is multifunctional serving as
a pressure gauge, monitoring the amount of pressure
being applied to the item being inflated, and changing air
pressure measurement units from PSI to BAR to KPA.
18
Status
Charging
Fully Charged
1) Press the wake up button to turn on the digital gauge.
2) Select desired measurement unit (PSI, BAR, KPA) by
pressing and releasing the mode button. Press once
for PSI, twice for BAR, and three times for KPA.
NOTE: The pressure readout on the gauge while
inflating is a measurement of the fluctuating pressure
between the item and the high pressure hose. To get
an accurate reading, stop inflating and follow above
instructions for reading the air pressure.
3) Automaticly shut off. The digital gauge will remain on
for up to five minutes.
3. INFLATOR OPERATION
The high pressure air hose can easily inflate high
pressure items like motorcycle, car, and bicycle tires.
(partial air mattresses, rafts can be inflated with
high pressure air hose, details please refer to the air
mattresses, floats store that sold them.)
1) To inflate objects, use the high-pressure air hose with
valve adapter.
2) Connect the suitable adapter of the high-pressure
air hose with valve adapter to the object you wish
to inflate. Depending on what you are inflating, also
chose the suitable adapters (19, 20, 21).
3) The pressure at the high-pressure air hose will be
displayed in the display screen.
4) The unit of the displayed pressure can be selected
with the unit overpressure button/wake up button
(PSI, KPA, and BAR).
5) The reduce pressure button allows the desired
pressure to reduced.
6) The increase pressure button allows the desired
pressure to be increased.
7) Switch on the equipment by pressing the selector
switch for inflator/blower mode button to "I" position.
8) The machine will then pump until the preset pressure
on the display is reached, then it will switch off.
9) After finishing working, press the selector switch for
inflator/blower mode button to "O" position.
WARNING! Observe the information
supplied by the tire manufacturer and
the vehicle manufacturer relating to the
recommended tire pressure.
WARNING! This equipment is not
calibrated! For a calibrated
measurement valve, check the actual tire
pressure using a calibrated meter after you
have inflated the tired yourself, e.g. at a
petrol station.
WARNING! Just before it is switched
off, the pressure which is shown in the
display screen can be 0.05-0.2 bar higher
EN