Publicidad
Idiomas disponibles
Idiomas disponibles
Warning! Never tighten the collet without first installing a
router bit in it. Tightening an empty collet, even by hand, can
damage the collet.
Warning! Do not use router bits with a cutting diameter in
excess of 34.9 mm in this tool.
Warning! Do not use straight router bits with a diameter larger
than 30mm.
To install the bit
Remove the motor unit from the base unit. Refer to
u
Removing the Motor from the Fixed Base (if needed).
Clean and insert the round shank of the desired router bit
u
into the loosened collet as far as it will go and then pull it
out about 1.6 mm.
Depress the spindle lock button (8) to hold the spindle.
u
shaft in place while turning the collet nut (16) clockwise
with the wrench provided.
Note: The unit is equipped with two spindle lock detents.
Note: Tighten collet nut securely to prevent the bit from
slipping.
To remove the bit
Remove the motor unit from the base unit (refer to
u
Removing the Motor from the Fixed Base/Removing the
Motor from the Plunge Base).
Depress the spindle lock button (8) to hold the
u
spindle shaft in place while turning the collet nut (16)
counterclockwise with the wrench provided.
Collets
Note: Never tighten the collet without first installing a router bit
in it. Tightening an empty collet, even by hand, can damage
the collet.
To change collet sizes, unscrew the collet assembly as
described above.
Install the desired collet by reversing the procedure. The collet
and the collet nut are connected. Do not attempt to remove
the collet from the collet nut.
Locking lever adjustment (Fig. E)
Excessive force should not be used to clamp the locking lever.
Using excessive force may damage the base.
When the locking lever is clamped, the motor should not move
in the base.
Adjustment is needed if the locking lever will not clamp
without excessive force or if the motor moves in the base after
clamping.
To adjust the locking lever's clamping force:
Open the locking lever (9) (base unit).
u
Using the hex wrench provided, turn locking lever
u
adjustment nut (10) in small increments.
Turning the nut clockwise tightens the lever, while turning
the nut anticlockwise loosens the lever.
(Original instructions)
Centering the subbase (Fig. F)
If you need to adjust, change, or replace a subbase, a
centreing tool is recommended. The centering tool consists of
a cone and a pin.
Loosen but do not remove the subbase screws (20) so the
u
subbase moves freely.
Insert the pin into the collet and tighten the collet nut.
u
Insert the motor into the base unit and clamp the locking
u
lever (9) on the base.
Place the cone on the pin and lightly press down on the
u
cone until it stops. This will center the subbase.
While holding down on the cone, tighten the subbase
u
screws.
Installing a fixed base edge guide (Fig. G)
Remove the motor unit from the base unit. Refer to Removing
the Motor from the Fixed Base.
Remove flat head screws from storage holes on
u
edge guide.
Slide edge guide (19) into edge guide slot (18) on side
u
of base unit. Insert the two flat head screws through the
appropriate holes in the subbase to secure the edge
guide. Tighten hardware.
Follow all instructions included with the edge guide.
u
Note: To remove the edge guide, reverse the above
procedure. After removing edge guide, always replace the two
flat head screws into the storage holes on the edge guide to
prevent loss.
Attaching a dust extraction system to the
Fixed base (Fig. H)
To connect the router to a dust extraction system for dust
collection, follow these steps:
Remove the motor unit (6) from the base unit. Refer to
u
Removing the Motor from the Fixed Base.
Attach dust extraction system attachment accessory (12)
u
to the base unit as shown. Tighten thumb screw (13)
securely by hand.
Attach hose adapter to dust extraction system attachment
u
accessory.
When using dust extraction system attachment, be aware
u
of the placement of the dust extraction system. Be sure
that the dust extraction system is stable and that its hose
will not interfere with the work.
Set-Up: Fixed base
Inserting the motor into the fixed base (Fig. I)
Open the locking lever (9) on the base unit.
u
Depress the motor release lever (14).
u
While depressing motor release lever, lower motor unit
(6) into the base unit (7) with depth adjust rod aligned to
opening in the base unit.
ENGLISH
9
Publicidad
