Hendi 201442 Manual De Instrucciones página 8

Grounding installation
GB
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Lid
2. Clamp lock
3. Ventilation holes
4. Oil fill in port
5. Oil level display
6. Drain oil port
7. Control panel
8. Sealing bar
9. Clamp for fixing vacuum bag
10. Chamber
11. Main ON / OFF knob
12. Screws
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig.2 on page 3)
13. SET button
14. Time adjust button
14.1: Increase / 14.2: Decrease
15. STOP button
16. Digital display
17. Light indicators (VACUUM TIME / SEALING / GAS / COOL-
ING)
18. Vacuum gauge
Spare parts or accessories
19. Wrench (1x)
20. Screw driver (1x)
21. Empty bottle with nozzle (1x)
22. A bottle of pump oil (Volume: 300ml) (1x)
Note: Vacuum bag is not included.
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
8
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
(Fig.1 on page 3, Fig.2 on page 3)
• Select the proper size of vacuum bag. (Bag width of 400mm).
Allow a minimum of 3 ~ 4 cm of extra spacing at the top to
ensure well sealing.
• With the lid (1) kept open, insert the power cord to the socket
at the rear of the machine and the power plug to a suitable
electrical power outlet.
• Then, turn the ON / OFF switch clockwise to the "ON " posi-
tion. "ON " will be shown on the digital display (16).
• Next, press SET button (13) to select the VACUUM TIME,
SEALING and COOLING process for setting.
• Then, press increase / decrease button (14) to adjust the time
of each process.
See below for the setting range of different operations:
1) Vacuum Time: 5 ~ 90 seconds (With 5 seconds interval)
2) Seal Time: Set up to 6 seconds (With 0,5 second interval,
descending)
3) Cooling Time: Set up to 10 seconds
• Put the food in a vacuum bag. Then, put the whole bag under
the fixing clamp (9) inside the chamber (10) of the machine.
• Please make sure that the opening of the vacuum bag is en-
tirely and properly under the seal bar (8) for sealing. And the
whole vacuum bag is locked properly by the fixing clamp (10)
inside the chamber (9).
• Close the lid (1) and put up the lid lock (2). The machine will
start vacuum-and-seal process automatically.
• After that, VACUUM TIME indicator (17) will blink in blue and
the machine will start countdown to show the remaining time
on the display (16).
• Similarly, SEALING & COOLING indicator (17) will blink in blue
and the machine will start the countdown. Remaining time of
sealing and cooling process will be shown on the display (16).
• Now, air inside the vacuum bag and chamber is sucked out
(9).
• A beep will sound when the sealing process is finished.
• "CLO" will be displayed on the display (16) for 15 seconds.
After that "ON " will be shown on the digital display (16).
• Put down the lid lock (2) to open the lid (1) and take away the
packaged food.
Note:
1) When the machine is under "vacuum" process, you can press
"STOP" button (15) to switch to "sealing" process instantly.
2) When the display shows "CLO", the machine is in idle mode.
In this mode, no matter which button you press, the machine
will not work. Just put down the clamp lock (2) and open the
lid (1). Then, the machine can return to normal operation.
3) After the process, check the completeness of the sealing. If
the seal is not correct, adjust the vacuum and sealing time.
4) Important: "GAS" function is not available with the light indi-
cators for this model.