Kicker KXMA800.8 Manual Del Propietário página 6

OPERATION
Mini-USB for internal use only; do NOT remove or tamper. KICKER is not responsible for any damage to
equipment resulting from connections made to this port.
AMP1
OFF/HP/LP
0 11 10 Hz 500
PRT
GAIN
FREQ.
KXMA800.8
GAIN
MATCH
X-OVER
Automatic Turn-On Selection: The KXMA series offers three different automatic turn-on modes that
can be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio
mode causes the REM terminal to have +12V out for turning on additional amplifi ers.
• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit.
Run 18 gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM
between the amplifi er's positive and negative power terminals. This is the preferred automatic turn-on
method.
• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC
Offset mode detects a 3V DC offset from the HI-Level speaker outputs when the source unit has
been turned on.
• Signal Sense Turn-On: The Audio setting is the fi nal alternative for Automatic turn-on. This is a
Signal Sense turn-on method that detects the incoming audio signal from your source unit and
automatically turns on the amp. This turn-on method will not work properly if the input gain control is
not set appropriately.
Fader Switches: Turn the Fader switch(es) OFF if you are running more than a single pair of RCA inputs
to the amplifi er. Turn the Fader switch(es) ON if you want to drive those channels from a single input. For
example, if you are using AMP 1, AMP 2, AMP 3, and AMP 4 RCA inputs, switch the AMP 1/AMP 2
FADER, AMP 2/AMP 3 FADER , and AMP 3/AMP 4 FADER buttons to ON.
Input Gain Control with Gain Matching: The input gain control is not a volume control. It matches the
output of the source unit to the input level of the amplifi er and features Gain Matching to prevent clipping
the input. For a quick setup, turn the source unit up to about 3/4 volume (if the source unit goes to 30,
turn it to 25). KICKER recommends using the test tones at www.kicker.com/support/ to reach the most
accurate and best performing settings. Next, slowly turn (clockwise) the gain on the amplifi er up until you
see the Gain LED light up or hear audible distortion, then turn it down a little. If the GAIN knob's backlight
comes on, the input is still clipping. For full instructions on Gain Matching, please see the next page.
Crossover Switches with Frequency Multiplier: Use the XOVER switches on the end panel of
the amplifi er to set the internal crossovers of AMPS 1 & 2 to OFF, HI-PASS, or LO-PASS, and the
crossovers of AMPS 3 & 4 to OFF, HI-PASS, LO-PASS, or BAND-PASS. When the switch is set
to OFF, a full bandwidth signal will be amplifi ed. Set the switch to HP if you want the amplifi er's internal
crossover to serve as a high-pass fi lter. Set the switch to LP if you want the amplifi er's internal crossover
to serve as a low-pass fi lter. Set the switch to BP when a specifi c frequency range is required. Never
change the crossover switches with the audio system on!
Set the 1X/10X frequency multiplier switch to the setting that is appropriate for your application. A
setting of 10X will set the range of the AMP 1 & AMP 2 crossovers to 100–5,000Hz, and the low pass
crossovers of AMP 3 & AMP 4 to 100–5,000Hz.
KICK EQ Bass Boost Control: The variable bass boost controls on the side of the KXMA800.8
amplifi er are designed to give you increased output, 0–6dB, at 40Hz. The setting for this control is
6
2021 KXMA 8-CH Amp Rev C.indd 6 2021 KXMA 8-CH Amp Rev C.indd 6
AMP2
OFF/HP/LP
1X/10X 1X/10X
RANGE 0 dB 6 0 11 10 Hz 500 RANGE 0
KICK EQ GAIN FREQ. KICK EQ
GAIN
MATCH
X-OVER
AMP3
OFF/HP/LP/BP
1X/10X
dB 6 0 11 0
10 Hz 500 40 Hz 500 LO-PASS
RANGE
GAIN KICK EQ
HI-PASS LO-PASS
GAIN
MATCH
X-OVER
AMP4
OFF/HP/LP/BP
1X/10X
dB 6 0 11 0
10 Hz 500 40 Hz 500 LO-PASS
RANGE
GAIN KICK EQ
HI-PASS LO-PASS
GAIN
MATCH
X-OVER
10/6/2020 7:10:59 AM 10/6/2020 7:10:59 AM
dB 6