Publicidad
Idiomas disponibles
Idiomas disponibles
Note: This machine is equipped with an electromag-
netic switch to prevent it from being unexpectedly
switched on when power source recovered.
6.2 Reversing switch (Abb. 6)
This shredder has an automatic overload pro-
tection and reverse switch.
A sudden blocking the device automatically (3 sec.)
can change the direction of rotation. The material is trans-
ported back (5 sec.). To prevent damage to the engine, the
circuit breaker (1) the power supply is automatically turned
off.
If the cutting blade still jammed after 5 seconds, so that the
motor can no longer run, press the rotational direction switch
REVERSE (2). The cutting blade rotates in the reverse direc-
tion and release the material so that you can remove it. Press
the green START button (3) to turn on the chopper.
6.3 Disassembling
For certain purposes, e.g. storage after use, etc, you can
disassemble the shredder in the reverse order as de-
scribed under "Assembling ".
6.4 Operating Instructions
Feeding
Feed the material to be chopped into the right side of the
feeding tunnel. The material is automatically pulled in by
the chopping knife.
Caution! Longer material standing out from the
machine could lash out when being pulled in by
the chopping knife! Keep a safety distance!
Warning! Always use the pusher (Fig.11) if you
try to push the material into the feeding tunnel.
Do not use your hands directly! Keep the push-
er well after use.
• Only insert as much material as will not block up the
feeding tunnel.
• Chop garden waste that has been stored for some
days and is wilted and damp alternately with branch-
es. This will prevent the chopping knife from getting
blocked up.
• Do not fill into the shredder any soft material such as
kitchen waste instead of compositing it.
• Widely branched material with leaves must be com-
pletely chopped before any new material is fed in.
• Take care that the chopped material can freely fall from
the discharge chute – danger of backing up!
• The ventilation slots must not be covered by the waste
bag or the chopped material.
6.5 Adjusting the cutting gear (Fig. 8)
The anvil blade 2 should be adjusted to have a distance
of 0 to 0,50 mm from the cutting blade 1 (fig. 8). This
distance should be kept to guarantee effective operation
of the mac.
Note: Soft materials or wet twigs can get torn instead of
cut properly due to wrong adjustment. Also a blunt an-
vil blade from frequent use produces the same problem.
On the right hand side of the shredder you will find the
blade adjustment knob (3). To adjust the distance turn the
screw to the right.
GB | Operating Instructions
1. For lighter material, you can cut through the material
2. If you are shredding heavy materials (such as harder
3. After you have completed the adjustment, check if
NOTE
1. Do not allow garden waste to accumulate before
2. Frequently monitor the build up/collection of shredded
3. Do not allow shredded material to build up and fill the
4. When the collection box is full, press the On/Off switch
WARNING!
Do not put your hands up inside the shredder's discharge
chute to clear away shredded material while the shredder
is switched on or connected to the mains supply.
NOTE
In normal use, do not switch off the garden shredder un-
til all of the shredded material has cleared the cutter as-
sembly. If the garden shredder is switched off too quickly,
remaining pieces of material may clog the blade assembly
and stall the motor when the shredder is switched back on.
7. Troubleshooting
The motor does not run
• The overload protection has responded.
• Power failure
• Safety switch on the collection box not locked in position.
The material to be chopped is not pulled in
• The chopping knife is running backwards.
• The material is jammed in the feeding tunnel
The material is clogging up in the feeding funnel
GB-6
completely turn the knob clockwise half a turn.
or large materials) they may need to be put through
the shredder twice, to crush the material before cutting
it completely. To loosen the adjusting screw, turn the
knob (3) anti-clockwise half a turn.
the blade cuts efficiently. To avoid and damage to the
shredder make sure that the cutting blade does not
come into contact with the anvil blade.
shredding as it will begin to compost, become too
damp and clog the cutting assembly. Dry material will
help most material to clear the ejection chute. Save
some dry sticks until last to help clean the blade area.
material.
inside of the shredders discharge chute.
to turn the garden shredder Off before emptying.
- Allow the machine to cool down for at least 1-2 min-
utes before re-starting. Push the overload switch (2).
- Set the reversing switch to position REVERSE. The
cutting blade rotates in the reverse direction and re-
lease the material so that you can remove it. Press
the green START button to turn on.
- Check the power supply cord, the plug and your
house connection fuse and RCD.
- Ensure collection box is in position and locked.
- Change the direction of rotation..
- Set the reversing switch to position (2). Pull the ma-
terial from the feeding funnel.
- Re-feed thick branches such that the chopping knife
does not immediately grasp the pre-cut notches again.
Publicidad
