Sime C Serie Manual De Instrucciones página 83

By following the instructions, it is now possible to set the time
and day of the week, follow the instructions below, Date (day,
month) and year
1
Time of day (MASTER)
Setting range
00.00.....23:59
a) Press the row selection pushbuttons to select
row 1.
b) Press the buttons to set the time of day.
The scheduling clock is set to the exact time; this is important
to ensure correct functioning of the controller's heating sche-
dule.
2
Day of the week (MASTER)
Setting range
1.....7
a) Press the row selection pushbuttons to select
row 2.
b) Press the pushbuttons to set the day of the
week.
The timer will be set to the selected day of the week
1 = Monday
2 = Tuesday
3 = Wednesday
4 = Thursday
3
Date (day, month) (MASTER)
Setting range
01 : 01 ..... 31 : 12
The controller day and month must be set to the current date.
This is important to make sure that the summer/winter set-
ting is switched correctly.
4
Year(MASTER)
Setting range
1999 ..... 2099
The controller year must be set to the current year. This is
important to make sure that the summer/winter setting is
switched correctly.
2.2.2 Installer level
These parameters must be configured and set by a heating technician.
This mode permits display of a number of parameters, including:
– the type of system recognised (53)
– the actual boiler temperature (55)
– the actual cascade delivery temperature (56)
– the actual cascade return temperature (57)
– the actual hot water temperature (59)
– the cascade delivery temperature pursued, or the cascade delivery
setpoint (66)
– the hot water temperature setpoint (69)
– the room temperature setpoint (70)
Refer to section 11 for a complete list of parameters.
Units
Hours: Minutes
Units
Day of the week
5 = Friday
6 = Saturday
7 = Sunday
Units
day month
Units
Year
Button Description
PRESS BOTH ROW SELECTION BUTTONS
1 FOR AT LEAST 3 SECONDS TO GO DIRECTLY TO
"INSTALLER" PROGRAMMING MODE
3s
PRESS THE SELECTION BUTTONS TO SELECT
2
THE DESIRED ROW
PRESS THE PLUS OR MINUS BUTTON TO SET
THE DESIRED VALUE. THE SETTING WILL BE
3 STORED INMEMORY WHEN YOU EXIT
PROGRAMMING MODE OR GO ON TO ANOTHER
ROW
TO EXIT "INSTALLER" PROGRAMMING MODE, PRESS
4
ONE OF THE OPERATING MODE BUTTONS.
If you do not press any button for about 8
minutes, the controller will automatically return
to its most recent operating mode
2.2.3 Manufacturer (OEM) level
This level is reserved for the boiler manufacturer only.
If the two Prog keys are number 1 and 2
1
and the two adjacent keys are numbered 3 and 4
3
the access code is: "1 2 4 3 4"
Refer to section 12 for a complete list of parameters.
Button Description
PRESS ONE OF THE UP/DOWN BUTTONS
1 TO GO DIRECTLY TO "END USER"
PROGRAMMING MODE
PRESS THE ROW SELECTION BUTTONS FOR AT
9s
2
LEAST 9 SECONDS
PRESS THE AND
THE ACCESS CODE COMBINATION REQUIRED.
IF THE COMBINATION OF BUTTONS IS CORRECT
3 CODICE
YOU WILL ENTER OEM PROGRAMMING MODE
IF THE CODE IS WRONG, THE DISPLAY WILL GO
ON TO "SETTING PARAMETERS FOR
THE HEATING TECHNICIAN".
PRESS THE SELECTION BUTTON TO SELECT THE
4
DESIRED ROW.
PRESS THE PLUS OR MINUS BUTTON TO SET THE
DESIRED VALUE.
5 THE SETTING WILL BE STORED IN MEMORY
WHEN YOU EXIT PROGRAMMING MODE OR
GO ON TO ANOTHER ROW.
TO EXIT "OEM" PROGRAMMING MODE, PRESS
ONE OF THE OPERATING MODE BUTTONS.
6
If you do not press any button for about 8
minutes, the controller will automatically return
to its most recent operating mode.
Do not change OEM settings!
Row
51
51...... 1 73
2
4
Row
1
°°
BUTTONS TO ENTER
1.....92
83