Vaillant aroSTOR VWL B 270/5 Instrucciones De Instalación Y Mantenimiento página 73

7 Handing the product over to the
operator
▶
Explain to the operator how the safety devices work and
where they are located.
▶
Inform the operator how to handle the product.
▶
In particular, draw attention to the safety information
which the operator must follow.
▶
Inform the operator of the necessity to have the product
maintained according to the specified intervals.
▶
Pass all of the instructions and documentation for the
product to the operator for safe-keeping.
▶
Inform the operator about measures taken concerning
the air pipe and inform them that they must not make any
changes.
8 Adapting the unit to the installation
8.1 Calling up the installer level
1. Press the menu button.
2. Turn the rotary knob until the INST.MENU menu ap-
pears in the display.
3. Hold down the clock button and the menu button for
three seconds.
◁
The first menu item of the installer level PV MODE
is displayed.
8.2 Setting the language
▶
If you want to change the current setting, press the menu
button.
▶
Turn the rotary knob until the display shows the language
setting.
▶
Press the rotary knob.
▶
Select the required language using the rotary knob.
▶
Press the rotary knob to confirm.
▶
Press the menu button to return to the original display.
8.3 Activating and setting photovoltaic mode
Condition: Existing photovoltaic installation
▶
If the control for the photovoltaic installation is connected
to plug no. 1 and no. 2 on the product's PCB, you must
activate PV MODE.
◁
The electrical energy generated is stored in the form
of domestic hot water. You can set two efficiency
levels for the photovoltaic installation.
◁
PV ECO = Low level of photovoltaic power gener-
ation. The heat pump generates an increased do-
mestic hot water temperature. The increased do-
mestic hot water temperature must be between the
normal domestic hot water temperature and 60 °C.
– Factory setting: 60 ℃
◁
PV MAX = High level of photovoltaic power genera-
tion. The heat pump and the immersion heater gen-
erate an increased domestic hot water temperature.
The increased domestic hot water temperature must
be between the domestic hot water temperature of
the PV ECO mode and 65 °C.
– Factory setting: 65 ℃
▶
Turn the rotary knob to set the mode. INST.MENU PV
MODE
8000015884_00 Installation and maintenance instructions
◁
You can select which function has higher priority
(photovoltaic mode or frost protection/eco mode)
▶
Select YES.
▶
Press the rotary knob to confirm the selection.
▶
Press the menu button.
▶
Set the required domestic hot water temperature.
▶
Turn the rotary knob to set the priority. INST.MENU → PV
MODE → PRIORITY.
◁
YES : The signals from connection plugs no. 1 and
no. 2 have priority over the frost protection and eco
mode.
◁
no : Frost protection and eco mode have priority over
the signals from connection plugs no. 1 and no. 2.
Note
When photovoltaic mode has the higher prior-
ity, domestic hot water is also heated during
periods that have not been set (e.g. holiday
mode and outside of programmed time peri-
ods).
If you only want to heat the domestic hot water
during the permitted time period, set the prior-
ity to no.
▶
Press the rotary knob to confirm the selection.
◁
The immersion heater is supplied with electricity in or-
der to use the energy from the photovoltaic installa-
tion.
◁
When the fan mode is activated (FAN MODE), op-
tion 3 can no longer be selected.
◁
The SHED DING function is not available.
▶
Press the menu button to return to the original display.
8.4 Reading the input data
1. If you want to read the product's input data, you must
select this menu. DI SPLAY → INST.MENU.
2. Press the rotary knob in the DI SPLAY menu.
◁
WATE R = Domestic hot water temperature in the
central section of the domestic hot water cylinder
◁
AIR INLET = Air temperature at the air intake
◁
T_EV APOR = Temperature of the evaporator
◁
If PV MODE is deactivated:
–
SHED DING : Connection contact no. 1/low-tar-
iff contact input (0: Contact opened; 1: Contact
closed)
–
FAN CONTR. : Connection contact no.
2/hygrostat input (0: Contact opened; 1: Contact
closed)
◁
If PV MODE is activated:
–
PV ECO : Connection contact no. 1 input (0:
Contact opened; 1: Contact closed)
–
PV MAX : Connection contact no. 2 input (0:
Contact opened; 1: Contact closed)
3. Press the menu button to return to the original display.
73