Hendi 239285 Manual Del Usuario página 9

4. If no any button on the control panel is pressed during oper-
ation for 2 hours, the appliance will then switch to Standby
mode automatically.
Suitable cooking equipment
Suitable
Bottom of Flat bottom
cookware (Fig.2 on page 3)
Material Cookware with iron,
cast iron, magnetic
stainless steel or
enamelled iron
bottom.
Diameter of Between 12 cm and
the bottom 22 cm.
Type of Cookware with a
cookware bottom thickness over
1.5 mm.
Note: Using a pan or pot that's not suitable for induction cook-
ing may damage the appliance.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
Not suitable
• Do not move the appliance while it is under operation. Dis-
Curved, uneven,
rounded bottom
(Fig.3 on page 3)
Cookware with
Troubleshooting
ceramic, glass, copper,
bronze, or aluminium
If the appliance does not function properly, please check the
bottom.
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Less than 12 cm or
more than 22 cm.
Completely closed
containers or cans.
Error code identification
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
been disconnected from the power supply and completely
cooled down.
damage it.
connect the appliance from power supply when moving and
hold it at the bottom.
Problems Possible cause
The appliance does - Power plug is
not switch ON. not connected
properly with the
electrical outlet.
- On/Standby (1)
button is not
pressed.
Cooling fan is - This is normal.
operating even The cooling
after the appliance fan continues
is switched to running in
Standby mode. Standby mode for
some time to cool
down all internal
elements.
Error Possible cause
codes
E 1 The temperature of the
appliance is too high
Cooling fan defective
E 2 The pan or pot is
overheated.
Possibly, the pan
becomes empty and
appliance will shut
down for protection.
E 3 The supply voltage
is abnormal. (Supply
voltage is too high or
too low)
DE
Possible solution
- Check the power
plug to make
sure it is con-
nected properly.
- Press the On/
Standby (1)
button to start
operation.
- Wait until the
cooling fan stops
rotating.
Possible solution
Clear all obstacles that
around the appliance.
Unplug the appliance,
remove the pan or pot,
wait until the appliance
is completely cool down.
Contact the supplier.
Unplug the appliance,
remove the pan or pot,
wait until the appliance
is completely cool down.
And make sure water is
inside the pan.
Make sure that the
appliance is connected
to a suitable electrical
power supply.
9