Makita DLS211 Manual De Instrucciones página 26

Kerf boards
This tool is provided with the kerf boards in the turn base to
minimize tearing on the exit side of a cut. The kerf boards are
factory adjusted so that the saw blade does not contact the
kerf boards. Before use, adjust the kerf boards as follows:
► Fig.15: 1. Kerf board
► Fig.16: 1. Left bevel cut 2. Straight cut 3. Right
bevel cut 4. Saw blade 5. Blade teeth
6. Kerf board
First, remove the batteries. Loosen all the screws (2
each on left and right) securing the kerf boards until the
kerf boards can still be easily moved by hand. Lower the
handle fully, then pull and turn the stopper pin to lock
the handle in the lowered position. Release the stopper
pin on the sliding pole and pull the carriage toward you
fully. Adjust the kerf boards so that the kerf boards just
contact the sides of the blade teeth. Tighten the front
screws (do not tighten firmly). Push the carriage toward
the guide fence fully and adjust the kerf boards so that
the kerf boards just contact the sides of blade teeth.
Tighten the rear screws (do not tighten firmly).
After adjusting the kerf boards, release the stopper pin and
raise the handle. Then tighten all the screws securely.
NOTICE:
After setting the bevel angle ensure
that the kerf boards are adjusted properly. Correct
adjustment of the kerf boards will help provide proper
support of the workpiece minimizing workpiece tear
out.
Maintaining maximum cutting capacity
This tool is factory adjusted to provide the maximum
cutting capacity for a 305 mm saw blade.
When installing a new blade, always check the lower limit
position of the blade and if necessary, adjust it as follows:
First, remove the batteries. Turn the stopper lever to
engaged position.
► Fig.17: 1. Stopper lever
Push the carriage toward the guide fence fully and
lower the handle completely.
Adjust the blade position by turning the adjusting bolt
with the hex wrench. The periphery of the blade should
come to the point where the front face of the guide fence
meets the top surface of the turn base and also it should
extend slightly below the top surface of the turn base.
► Fig.18: 1. Adjusting bolt
► Fig.19: 1. Top surface of turn base 2. Periphery of
blade 3. Guide fence
With the batteries removed, rotate the blade by hand
while holding the handle all the way down to be sure
that the blade does not contact any part of the lower
base. Re-adjust slightly, if necessary.
After adjustment, always return the stopper lever to the
original position.
WARNING:
After installing a new blade and
with the batteries removed, always be sure that
the blade does not contact any part of the lower
base when the handle is lowered completely. If
a blade makes contact with the base it may cause
kickback and result in serious personal injury.
Stopper arm
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, turn the
stopper arm in the direction of the arrow as shown in the
figure. Turn the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
► Fig.20: 1. Stopper arm 2. Adjusting screw
Adjusting the miter angle
CAUTION:
After changing the miter angle,
always secure the turn base by tightening the grip
firmly.
NOTICE:
When turning the turn base, be sure to
raise the handle fully.
► Fig.21: 1. Lock lever 2. Grip 3. Releasing lever
4. Pointer
Rotate the grip counterclockwise to unlock the turn
base. Turn the grip while holding down the lock lever to
move the turn base. Align the pointer with your desired
angle on the scale then tighten the grip.
NOTE: If you depress the releasing lever, you can
move the turn base without holding down the lock
lever. Tighten the grip at your desired position.
This miter saw employs positive stop function. You can
set 0°, 15°, 22.5°, 31.6°, 45°, and 60° right/left miter
angle quickly. To use this function, move the turn base
close to your desired positive stop angle while holding
down the lock lever. Then release the lock lever and
move the turn base to your desired positive stop angle
until the turn base is locked.
Adjusting the bevel angle
NOTICE:
Always remove the upper guide fences
and vertical vise before adjusting the bevel angle.
NOTICE:
When changing bevel angles, be sure
to position the kerf boards appropriately as
explained in the "Kerf boards" section.
NOTICE:
When tilting the saw blade, be sure to
raise the handle fully.
NOTICE:
Do not tighten the knob too hard. Doing
so may cause malfunction of the locking mecha-
nism of the bevel angle.
1. Turn the knob on the slide pole counterclockwise.
► Fig.22: 1. Knob
2. Pull and turn the latch lever to the position as
illustrated.
► Fig.23: 1. Latch lever
3. Match the pointer with your desired angle on the
scale by moving the carriage then tighten the knob.
► Fig.24: 1. Bevel angle scale 2. Pointer
To tilt the carriage to the right, tilt the carriage to the left
slightly and then tilt it to the right while pressing down
the releasing button.
► Fig.25: 1. Releasing button
26 ENGLISH