VERTO 50G273 Manual De Instrucciones página 13

• Pull the locking ring (12) away and slide the drill chuck (1)
onto the spindle until you can clearly hear the lock snaps in
(it may be necessary to rotate the drill chuck slightly so it can
reach appropriate position).
INSTALLATION AND REPLACEMENT OF WORKING TOOLS
IN THE SPINDLE HOLDER
• Place appropriate working bit directly in the spindle holder
(13) (fig. F).
• Ensure the bit is inserted to the end and is properly installed.
• To remove the working tool, pull the working bit out of the
spindle holder.
Use additional driver bit adapter with short driver bits. It is
recommended to always make a pilot hole before screwing
screws with the screwdriver. When a short driver bit is installed
in the spindle, it is not necessary to remove it when installing
the drill chuck (fig. G).
RIGHT-LEFT DIRECTION OF ROTATION
Choose direction of spindle rotation with the direction
selector switch (4) (fig. H).
Clockwise rotation – set the switch (4) to the extreme left
position.
Counter-clockwise rotation – set the switch (4) to the
extreme right position.
* In certain cases position of the switch related to rotation may be different than
specified. Please refer to graphic signs located on the switch or tool body.
Safe position of the direction selector switch (4) is in the
middle, it prevents accidental starting of the power tool.
• Drill cannot be started, when the switch is in this position.
• Use this position of the switch to change drills or bits.
• Before starting the tool make sure the position of the
direction selector switch (4) is correct.
Do not change direction of rotation when the drill spindle
is rotating.
CHANGE OF GEAR
The gear switch (3) (fig. I) allows to increase the rotational
speed range.
Gear I: small speed range, big torque
Gear II: greater speed range, smaller torque.
Set the gear switch in position appropriate for the works to
perform. When the switch is blocked and cannot be moved,
turn the spindle slightly.
Never change the gear switch position when the drill is
operating. It may damage the power tool.
Long lasting drilling at low rotational speed of the spindle
may cause motor overheating. Make periodic breaks
in operation or allow the tool to operate at top speed
without load for approximately 3 minutes.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the drill with a dry cloth or blow with compressed air
at low pressure.
• Do not use any cleaning agents or solvents, they may
damage plastic parts.
• Clean ventilation holes in the motor casing regularly to
prevent device overheating.
• Store the drill in a dry place, beyond reach of children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized
by the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless Drill 50G273
Parameter
Battery voltage
Battery type
Battery capacity
Range of idle rotational speed
Chuck range
Torque control range
Max. torque (soft drive)
Max. torque (hard drive)
Protection class
Weight, drill with battery
Year of production
50G273 defines type and indication of the device
Parameter
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Battery charging time
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration
Noise and vibration information
Noise produced by the device is defined with: level of
produced sound pressure Lp
(where K is measurement uncertainty). Vibrations produced
by the device are defined with vibration acceleration value a
(where K is measurement uncertainty).
Sound pressure Lp
acceleration a specified in this manual have been measured
h
in accordance with EN 60745. Specified vibration level a
can be used to compare tools and for initial evaluation of
exposition to vibrations.
13
Value
10,8 V DC
Li-ion
1300 mAh
0-350 / 0-1350
min
0,8-10 mm
1 – 18 plus drilling
19 Nm
35 Nm
1,1 kg
Charger
Value
230 V AC
50 Hz
13,5 V DC
350 mA
3-5 h
0,07 kg
Lp = 67dB (A) K=3dB (A)
A
Lw =78 dB (A) K=3dB (A)
A
a =1,9 m/s K=1,5 m/s
2
h
and level of sound power Lw
A
, sound power Lw and vibration
A A
-1
III
2020
II
2020
2
A
h
h