Publicidad
Idiomas disponibles
Idiomas disponibles
ENGlIsh
working environment or pose an increased health risk to
the operator and those in close proximity.
•
Use clamps or other practical ways to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body is unstable
and may lead to loss of control and injury.
•
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
•
An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety. The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than
18 gauge. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. When
using more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum Gauge for Cord sets
Total length of Cord in Feet
Volts
120 V
25 (7.6)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
ampere rating
More
Not
Than
More
Than
0
6
18
6
10
18
10
12
16
12
16
14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
26
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
american Wire Gauge
16
16
16
14
16
14
12
Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation–
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all documentation
..................... do not expose to rain
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories. An
accidental start‑up can cause injury.
Changing Blades
To Install the Blade (Fig. A–C)
WARNING: Disconnect tool from power source before
service, adjustment, installing or removing accessories.
1. Retract the lower blade guard
spindle against the inner clamp washer, making sure
that the blade will rotate in the proper direction (the
direction of the rotation arrow on the saw blade and the
teeth must point in the same direction as the direction of
rotation arrow on the lower blade guard). Do not assume
that the printing on the blade will always be facing you
when properly installed. When retracting the lower
blade guard to install the blade, check the condition
and operation of the lower blade guard to assure that
it is working properly. Make sure it moves freely and
does not touch the blade or any other part, in all angles
14
and depths of cut.
12
2. Place outer clamp washer
12
letters side facing out.
3. Thread blade clamping screw
hand (screw has left‑hand threads and must be turned
counterclockwise to tighten).
4. Depress the blade lock button
saw spindle with the hex key
engages and the blade stops rotating.
5. Tighten the blade clamping screw firmly with the
blade wrench.
NoTE: Never engage the blade lock while saw is running, or
engage in an effort to stop the tool. Never turn the saw on
while the blade lock is engaged. Serious damage to your saw
will result.
To Replace the Blade (Fig. A–C)
WARNING: Disconnect tool from power source before
service, adjustment, installing or removing accessories.
1. To loosen the blade clamping screw
blade lock button
hex key
14
stops rotating. With the blade lock engaged, turn the
blade clamping screw clockwise with the hex key (screw
has left‑hand threads and must be turned clockwise
to loosen).
2. Remove the blade clamping screw
washer
13
8
and place blade on saw
13
on saw spindle with the
9
into saw spindle by
3
while turning the
14
until the blade lock
and turn the saw spindle with the
3
until the blade lock engages and the blade
9
only. Remove old blade.
, depress the
9
and outer clamp
Publicidad
