Publicidad
Idiomas disponibles
Idiomas disponibles
For wall mounting
1)
Un-install speaker box and the stand in the revise way from above
2)
Use the wall-mounting template supplied with the unit to make anchor hole marks on the wall. Make sure the marks are level.
3)
Drill 1/4" holes on the marks.
4)
Insert the plastic anchor supplied with unit it is flush with the wall.
5)
Insert the screw and tighten the screw 4mm away from the wall. (approximately the width of 2 pennies) hang the main unit and
speakers to the screw as indicated below:-
Connection
1.
Connect the DC plug (28) to the DC in jack of the unit then plug the AC/DC adaptor(27) to the ac outlet
2.
When you first plug the unit into the mains, the unit will go to standby mode and the standby LED indicator (7) will light up.
3.
Connect the speaker wire to the speaker jack (26) located on the side of unit.
4.
Turn on the unit by On/Standby button (5), if the LCD display (12) is on with backlighting, it means the power supply is normal. Now your
system is ready to play the music.
Setting the clock
1.
Set unit in standby mode.
2.
Press & hold the " Mem/Clk-adj " button (14), the LCD display (12) will show " 12hr " and flashing. Press skip up
button (15,21) to select the appropriate area hour format (12hr/24hr). Press "Mem/Clk-adj" button (14) again to confirm.
3.
The LCD display (12) will display the first & second digit of " 00 " is flashing. Press skip up
the correct hour. Press " Mem/Clk-adj " button (14) to store the correct hour.
4.
The third & fourth digit of " 00 " is flashing, press the skip up
press " Mem/Clk-adj " button (14) to store the correct minute.
The pre-set time will be re-set completely if dis-connecting the main power supply. You are recommended to
switch the system into standby mode for convenience usage.
Listening to radio
Manual tuning
1. Tune on the unit by press On/standby button(5)
2. Press Function button (6) to select " Radio " mode.
3. Tune to the required station by pressing the tune " + " or " − " button (15,21).
4 . Adjust Volume up/down button (10,4) to the desired volume level.
Auto tuning
1.
Press Function button (6) to select " Radio " mode.
2.
Press and hold the tune " + " or " − " button (15,21) for 1-2 seconds and then release.
3.
The unit will start seeking automatically and stop until a radio station is reached.
4.
Repeat step 2 & 3 until the desired radio station is being reached.
5.
Adjust volume up/down button (10,4) to the desired volume level.
Preset stations
You can store up to 10 radio stations in the memory.
1.
Set to tuner mode.
2.
Turn to the desired radio station by " manual" or " auto " tuning method.
3.
Press " Mem/Clk-adj " button (14) to enable program function & " MEM " indicator is show on LCD display (12)
4.
Press " Pre-up
or Pre-dn
5.
Press " Mem/Clk-adj " button (14) again to confirm the setting.
6.
Repeat step 2 to 5 to store other stations.
7.
Now you can select the presets stations in order by pressing the " Pre–up
The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to
switch the system into standby mode for convenience usage.
There are 10 seconds for programming state, after program mode active 10 sec had no any button pressed. This state would resume
to normal tuner mode automatically.
You can overwrite a present station by storing another frequency in its place.
" button (17,18) to select the desired station memory for storage.
or skip down
button (15,21) to set the correct minutes. Then
" button (17) or Pre-dn
2
or skip down
or skip down
button (15,21) to set
button (18).
Publicidad
