Publicidad
Idiomas disponibles
Idiomas disponibles
Jandy
WaterColors RGBW LED Lights | Installation & Operation Manual
®
7.2
12V Small Light Driver (PCB)
Replacement
1.
Remove both quick disconnect wires from the
PCB. Note that the black wire is connected to
ACN (TP-2) and the White wire is connected to
ACL (TP-1).
2.
Remove two (2) nuts and two (2) washers.
3.
Remove the light driver from the light fixture.
4.
Apply thermal grease to the back of the new light
driver board.
5.
Place new light driver into the fixture with the
orientation shown in Figure 7.
6.
Secure the light driver with one (1) washer and
one (1) nut on the right side of the light driver.
Torque to 12 in-lbs.
7.
Place a washer on the other stud and place the
green ground wire terminal on the washer and
Black (12V)
secure both with the nut. Torque to 12 in-lbs.
8.
Plug in the quick disconnect wire (white) onto the
terminal ACL (TP-1) of the light engine.
TP-2
9.
Plug in the quick disconnect wire (black) onto
Nylon
terminal ACN (TP-2) of the light engine.
R1
Washer
7.3
120V Small LED Board Replacement
Nut
U4
1.
Disconnect power and wait 5 minutes.
TP-VO
RD1
2.
Remove two (2) screws and six (6) washers.
WD1
R5
Q1
3.
Unplug the board connector from the light engine.
R4
Q2
4.
Remove the LED board from the heat sink. If
U3
you are also replacing the driver board, you can
proceed now to step 7.4
5.
Apply thermal grease to the back of the new LED
board.
6.
Place new LED board into the heat sink with the
orientation shown in Figure 7.
7.
Secure the LED board with two (2) screws and
two (2) washers.
8.
Plug in the board connector.
7.4
120V Small Light Driver (PCB)
Replacement
1.
Disconnect power and wait 5 minutes.
2.
Remove LED board as instructed in step 7.3
3.
Remove 2 screws from the heat sink and remove
the heat sink.
4.
Remove both quick disconnect wires from the
PCB. Note that the black wire is connected to
ACN and the White wire is connected to ACL.
5.
Remove 2 metal posts from the driver board.
6.
Remove driver board and place new light driver
board into the fixture with the orientation shown
in Figure 7.
Green
White (12V)
TP-1
TP-2
TP-1
AC2-Black
AC1-White
GND
RS9
PF
RS8
5V
Q9
18V
Secure
Q10
CH1
D1
D2
D3
D4
TP-V
First
J17
Q7
GD2
GD3
GD4
Q8
GD1
CSHVLED-L
2016-05-28
J16
RD2
RD3
RD4
RD5
RN3
WD2
WD3
WD4
WD5
RN4
BD4
RN2
BD3
TP-G
BD1
BD2
R16
R2
TP-T
CON2
R9
J03
R15
U1
Q6
C3
Q5
R13
C2
RN1
R11
U2
R14
J07
J09
RS5
J08
Q3
Q4
12V Wiring LED Board
Black (12V)
TP-2
Nylon
R1
Washer
AC2-Black
GND
PF
5V
Nut
U4
18V
CH1
TP-VO
GD1
RD1
RD2
WD2
WD1
R5
Q1
BD1
J03
R4
Q2
U3
12V Wiring LED Board
CSHVLED-C
D01
D02
D03
D04
C1
C0
RS2
RS1
R12
R13
RS3
R14
R09
R11
R15
C04
T01
R10
U1
J01
C05
R15A
R16
R19
R20
EC1
R21
D06
U2
J02
CY1
120V Wiring Driver Board
Figure 7.
Small Light Engine (PCB) Replacement
and Wiring
7.
Insert metal posts back on to the screw studs.
8.
Plug in both quick disconnect wires, white onto
the terminal ACL of the light driver and black
onto the ACN.
9.
Align heat sink to the metal posts
10.
Secure the heat sink with 2 screws
11.
Apply thermal grease to the back of the new LED
board.
12.
Place new LED board into the heat sink with the
orientation shown in Figure 7.
13.
Secure the LED board with two (2) screws and
six (6) washers.
14.
Plug in the board connector.
Page 11
ENGLISH
Green
White (12V)
TP-1
TP-2
TP-1
AC1-White
RS9
RS8
Q9
Secure
Q10
D1
D2
D3
D4
TP-V
First
J17
Q7
GD2
GD3
GD4
Q8
CSHVLED-L
2016-05-28
J16
RD3
RD4
RD5
RN3
WD3
WD4
WD5
RN4
BD4
RN2
BD3
BD2
TP-G
TP-T
R16
R9
R2
CON2
R15
U1
Q6
C3
Q5
R13
C2
RN1
R11
R14
U2
J07
J09
RS5
J08
Q3
Q4
ACN (Black)
L1
ACN
ACL (White)
Black
R01
Spa Light
R02
Driver
RV1
TP-N
CX1
F1
TP-FL
TP-L
R03
GD1
R04
15V
PF
5V
U3
R05
R24
R25
C06
D07
EC2
R23
GND
ZD1
ZD2
R22A
Publicidad
