Publicidad
Idiomas disponibles
Idiomas disponibles
Menú 757 – Modo de balanceo y ajuste de flujos
= scroll menu items
V AV C onf ig
COnf
(configuration)
SEtc
(settings)
bAL
(balancing)
mot
(motor)
End
(exit menu)
Exit menu and return
to normal operation
*** To save any changes, press
*** To the previous step without saving, press
Reseteo a configuración de Fábrica
Esta acción borrará todas las configuraciones actuales y serán reemplazadas por la configuración de fábrica.
El jumper (JP1) del sensor digital de pared debe colocarse en posición "RUN" (Operation Mode). Vea página 6 de este
1.
manual
Durante la secuencia de arranque del controlador y del sensor digital de pared, presione y mantenga los botones.
2.
Aparecerá la pantalla "Enter Password". Ingrese el número 372 utilizando los botones de flecha.
3.
Utilice los botones [
4. Utilice los botones de flecha para seleccionar YES y presione el botón [
https://www.innes.com.mx/
P r essur Fil t er T im e In S ec
Air f l ow Int gr al t im e in M in
2 sec
0 min
(1-10 sec)
AV.100
M axim um C ool ing A ir f l ow
1000
Air f l ow Set t ing
COOl
HEAt
M axim um H eat ing A ir f l ow
1000
C l ose M ot or
130
Air f l ow Bal ance
MSV.47
M inim um Air f l ow
CLOs
(close)
133
Min
(minimum flow)
mA
M axim um A ir f l ow
(maximum flow)
OPEn
135
(fully opened)
O pen M ot or
M ot or O ver ide
MSV.37
135
Auto
(automatic)
OPEn
(open)
M ot or DIR -RE V
CLOs
(close)
DIR
FLOl
(airflow low)
REV
FLOh
(airflow high)
Flow value depends on the actual mode of the system:
Heating = heating airflow
Cooling = cooling airflow
] y
para cambiar entre dígitos.
INCTR14VAV Standard
Air Fl ow Scal e
(0-60 min)
AV.106
1
10
100
AV.103
M inim um C ool ing Air f l ow
200
(Min cool airflow to Kfactor)
(0 to max cool airflow)
AV.105
M inim um Heat ing Air f l ow
200
(Min heat airflow to Kfactor)
(0 to max heat airflow)
AV.114
Go to "mot"
(see note)
AV.114
Go to "mot"
(same as Close Motor)
AV.112
Go to "mot"
(see note)
AV.112
Go to "mot"
(same as Maximum Airflow)
BV.40
(direct)
Returns to
(reverse)
run mode
on INTRM24VAV***
on INTRM24VAV***
].
Controlador de VAV
Sel ect A ir f l ow KF act or
MSV.41
1200
Range depends on air flow scale
from previous step:
(1) =
100 - 9995
(10) = 10.0 - 999.5
AV.102
(100) = 1.0 - 99.9
"HEAt"
AV.104
Go to "bAL"
Adjusts the offset of the airflow
reading. Offset range depends on
selected air flow scale in Conf menu.
When balancing, use only two of
(1) =
+/-500
the four modes available; either:
(10) = +/-50.0
(100) = +/-5.00
Close Motor and Open Motor
or
Displays the airflow based on the
Kfactor. Range depends on air flow
Minimum Airflow and Maximum
scale in Conf menu:.
Airflow (more precise)
(1) =
100-9995
(10) = 10.0 - 999.5
(100) = 1.00 - 99.95
"SEtc"
AV.101
Page | 14
Publicidad
