Publicidad
Idiomas disponibles
Idiomas disponibles
This equipment is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
people with no experience or knowledge of the equipment, unless it
is done under the supervision or in accordance with the instructions
for use of the equipment by persons responsible for their security.
Make sure that children do not play with the equipment.
PREPARATION
Before connecting the washer to the mains, always make sure that
the mains voltage corresponds to the voltage specified on the rating
plate of the device.
To connect the washer, use a suitable power cord suitable for
outdoor operation and protected against splashes of water.
The plug connection of the cable with the extension cord must not
lie in the water.
USE
It is not allowed to use the washer if the power cord is damaged or
other important part of the device is damaged, e.g. safety elements,
high pressure hoses, spray gun.
If a power cord extension cord is used, the plug and socket should
be splash-proof.
Incorrect extension of the power cord may result in electric shock.
If the pressure relief switch does not trip, do not allow the washer to
run longer than two minutes with the gun in the closed position. After
this time, the temperature of the water in the circuit will increase and
may damage the pump seals.
The washer is intended for indoor and outdoor use.
Never touch the plug or socket with wet hands.
All electrically conductive parts in the workplace must be protected
against water.
The plug on the extension cord must be tight and not in water.
Pay special attention not to damage the power cord as a result of
running over, bending or chafing. You also need to protect it from
heat and sharp edges.
Before switching on the machine, fully unwind the extension cord
from the drum.
Never leave the device running unattended.
Turn off the power and water supply during longer breaks in use.
Do not leave the operating device unattended.
Work in potentially explosive areas is forbidden.
MAINTENANCE
Disconnect the washer from the power supply when carrying
out maintenance work.
To ensure safety, use only original spare parts or parts approved by
the manufacturer.
Use only high-pressure hoses, couplings and accessories
recommended by the manufacturer. These are the elements that
determine the safety of the device user.
Inspect the unrolled power cord for damage or wear before
use. Have a damaged cable replaced at the manufacturer's service.
If the power cord becomes damaged during operation, disconnect
the power immediately. DO NOT TOUCH THE CABLE BEFORE
DISCONNECTING THE POWER SUPPLY.
ATTENTION: Despite the use of an inherently safe structure, the use of
safety measures and additional protective measures, there is always a
residual risk of injury during work.
Explanation of the pictograms used:
1
2
6
7
1. NOTE: Take special precautions to
2. Read the operating manual, observe the warnings and safety
conditions contained in it,
3. Use personal protective equipment,
4. Disconnect the power cord before starting maintenance or repair
activities,
5. Use protective clothing,
6. Protect against rain,
7. Do not direct the stream at people, animals and live installations,
8. Second class of protection,
9. Risk of injury by high pressure,
3
4
5
8
9
10
10. Keep the children away.
CONSTRUCTION AND APPLICATION
A pressure washer is a class II electrical protection device designed for
cleaning surfaces and objects under high water pressure. The pressure
washer is widely used in households, transport, construction, agriculture
and other areas of activity. It is especially suitable for washing cars, car
trailers, buildings, boats, ceramic tiles, etc. Appropriate accessories
enable mixing of cleaning agents. The device is placed on an ergonomic
trolley with handles for accessories and a drum for high pressure hose.
Do not use the device contrary to its intended use.
Description of graphic pages
1
Lance
2
Extension lance
3
Adjustable nozzle
4
Detergent container
5
Lance handle
6
Cleaning pin
7
Instruction
8
Hook for high pressure hose
9
Screw set
10
Plastic cork
11
Quick coupler with built-in filter
12
Water inlet connection
14
On / off switch
15
Power cord
16
Power cord holder
17
Transport handle
18
High pressure hose reel with integrated high pressure hose
19
High pressure hose
20
Cut-off switch
21
Hose reel drum crank
Accessories 59G621
1
High-pressure washer
2
Adjustable nozzle 2 pcs; flat jet, circular jet
3
Lance extension
4
Lance
5
Cleaning pin
6
Screws (2 pcs)
7
User documentation
8
Power cord holder
9
Quick coupler with filter
10 Lance holder
11 Drum crank
12 Accessory holder
13 Detergent container
14 brush
15 Rotary brush for paving stones
PREPARING THE WASHER FOR WORK
Lance assembly
Attaching the lance with the lance extension Fig. C1 lock the parts by
turning to the left and then attach the adjustable nozzle to the lance
extension Fig. C2 by pressing until you hear a clear click
Note: When attaching, align the protrusion on the front lance with the
groove on the lance extension while keeping the button pressed.
Mounting the hook for accessories
Screw the accessory hook (8) firmly to the main unit with the 2 screws (fig
D1) packed together with the manual, please check and find them after
unpacking.
Note: All screws are packed in a bag
Installing the Hose Reel Crank
Attach the hose reel crank (21) to the drum tightly but carefully until it clicks
into place Fig. D2
Installation of the lance holder and the power cord
Install the gun holder (5) by sliding it onto the guide, mount the power cord
holder (16) in a similar way until you hear a click Fig. E
Connecting the pressure hose to the lance
Completely unwind the high pressure hose, attach the end of the high
pressure hose to the lance fig. F1 .
Note: After connecting the high pressure hose, check the connection
by gently pulling on the hose to make sure it stays connected. Press
the lock button and pull to disconnect the high pressure hose.
Note: To easily disconnect the hose, pull the trigger to drain the
water from the lance and washer after finishing work, the switch is in
the "OFF / 0" position
8
Publicidad
