Publicidad
Idiomas disponibles
Idiomas disponibles
Troubleshooting Tips... Before you call for service
Problem
Clothes too wet
Blinking Spin light
or Spin light on at
end of cycle
Pilling
Snags, holes, tears,
rips or excessive
wear
Wrinkling
Sounds
"Clicking"
Back and forth
"swoosh"
"Clicking" behind
Control during fill
Water flow changes
during fill
Motor sounds during
spin
"Humming"
"Gurgling"
Water "swishing"
Washer rocking/
moving
"Squeaking" sound
Washer sounds that may be different from your prior washer:
Clicks, water flowing, gear sounds followed by pauses, and electric hum sounds
are all part of the normal wash cycle.
To listen and watch videos of normal washer operation, please go to
http://products.geappliances.com/appliance/gea-support-search-content?contentid=23061
or scan the QR code.
28
Possible Causes
No spin selected
Incorrect cycle selected
Wash load out of balance
Out of balance
condition has been
detected
Result of normal wear on
poly-cotton blends and
fuzzy fabrics
Pins, snaps, hooks,
sharp buttons, belt
buckles, zippers and
sharp objects left in
pockets
Undiluted chlorine
bleach
Chemicals like hair
bleach or dye, permanent
wave solution
Incorrect wash and dry
cycles
Improper sorting
Overloading
Repeated washing in
water that is too hot
Possible Causes
Shifter mechanism is
engaging or disengaging
Electric motor reversing
direction
Automatic Temperature
Control Valve
Automatic Temperature
Control Valve
Motor ramping up/down
during spin cycle
Water drain pump
Drive motor
Water drain pump
Washing process
Washer leveling legs
uneven
Washer not level and
rubbing on cabinet
Select a spin option.
Make sure the cycle selected matches the load you are washing.
Some fabrics will feel wetter when rinsed with cold water.
Redistribute load in washer and run through Drain & Spin cycle.
Allow cycle to continue and finish.
If load is wet at the end of the cycle, even out load and run a
Drain & Spin cycle.
While this is not caused by the washer, you can slow the pilling
process by washing garments inside out.
Fasten snaps, hooks, buttons and zippers.
Remove loose items like pins, objects in pockets and sharp
buttons.
Turn knits (which snag easily) inside out.
Check bleach package instructions for proper amount.
Never add undiluted bleach to wash or allow clothes to come in
contact with undiluted bleach.
Rinse items that may have chemicals on them before washing.
Use Speed Wash cycle with Extra Rinse option.
Match Cycle selection to the type of fabric you are washing
(especially for easy care loads).
Avoid mixing heavy items (like jeans) with light items (like blouses).
Try a fabric softener.
Loosely load clothes in the washer basket.
Wash in warm or cold water.
The drive system will engage at the start of agitate and disengage
when agitate is complete. This occurs multiple times during the
wash.
This sound is the motor rotating back and forth to clean your
laundry.
Two valves mix cold and hot water. The "clicking" is when either
valve turns on or off to raise or lower the fill water temperature.
Two valves mix cold and hot water. The "clicking" is when either
valve turns on or off to raise or lower the fill water temperature.
The motor will speed up incrementally during the spin cycle.
When spin is complete, it will coast until it stops.
The drain pump will make a humming sound when pumping out
water after agitation stops and continue until spin is complete.
The drive motor will make a "humming" sound during the wash and
spin phases of the cycle.
When the pump starts drawing in air, It starts to gurgle. The washer
should then begin spinning and the sound will continue until it is
done spinning.
Water swishing while the unit is agitating is normal, especially with
smaller loads.
To level the washer, adjust the leveling legs by rotating the
individual leg in the proper direction for up or down.
To level the washer, adjust the leveling legs by rotating the
individual leg in the proper direction for up or down.
What To Do
Reason
49-3000346 Rev 0
Publicidad
