Virutex FRE317VD Manual De Instrucciones página 15

7722118 D. ext. 20 for bits Ø up to 16
7722119 D. ext. 27 for bits Ø up to 23
7722114 D. ext. 30 for bits Ø up to 26
1745838 UF317S Cutting guide with suction cups and
clamps.
9045754 Complete rail, length 1.40 m
9045755 Complete rail, length 2.40 m
6045756 Suction cup (set of 2)
6045710 Set of 2 clamps
9045812 Jointing kit for cutting guide
6045665 Dual square accessory
6045669 Guide accessory for circular cutting
6045715 UC60 Universal guide accessory for circular
cutting
5000000 PL11 Dovetail attachment
6045702 PFE60 Template for trimming work tops
6640125 Bit for AGB fittings
1745927 ASU317S Joining clamp
1745928 ATU317S Joining straps
14. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-17 and EN 60745-1 and serve as a basis for com-
parison with other machines with similar applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
15. WARRANTY
All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, exlcuding any domage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
16. RECYCLING ELECTRICAL EQUIPMENT
Never dispose of electrical equipment with domestic was-
te. Recycle equipment, accessories and packaging in ways
that minimise any adverse effect on the environment.
Comply with the current regulations in your country.
Applicable in the European Union and in European
countries with selective waste collection systems:
If this symbol appears on the product or in the accom-
panying information, at the end of the product's useful
life it must not be disposed of with other domestic waste.
In accordance with European Directive 2002/96/EC, users
may contact the establishment where they purchased the
product or the relevant local authority to find out where
and how they can take the product for environmentally
friendly and safe recycling.
VIRUTEX reserves the right to modify its products
without prior notice.
F R A N Ç A I S
PROFILEUSE D'ANGLE FRE317VD
(Images page 52)
Important
Avant d'utiliser la machine, lire at-
tentivement ce MODE D'EMPLOI et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ, ci-jointe. S'assurer de bien
avoir compris ces instructions avant de
commencer à travailler avec la machine.
Conserver les deux modes d'emploi pour
de futures consultations.
1. INSTRUCTIONS DE SÉCURITÉ POUR LE
MANIEMENT DE LA PROFILEUSE
- Vérifier avant de brancher la machine que la tension
d'alimentation correspond à celle indiquée sur la plaque
des caractéristiques.
- Toujours maintenir les mains éloignées de la zone de
coupe et toujours tenir la machine par ses poignées.
- Il est recommandé de travailler avec un aspirateur de
copeaux pour prolonger la durée de vie de la fraise et
éviter qu'elle se casse.
- Débrancher la machine du secteur avant toute opé-
ration d'entretien.
- Toujours utiliser des pièces de rechange d'origine
VIRUTEX.
15