Sthor 78127 Manual página 15

GB
tric tools generate sparks, which may cause a fi re in case of contact with infl ammable gases or vapours. Do not allow children
and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fi t the mains socket. Do not modify the plug. Do not use any adapters whatso-
ever in order to adapt the plug to the socket. Unmodifi ed plug which fi ts the socket reduces the risk of an electric shock. Avoid
contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body increases the risk of an
electric shock. Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool
increases the risk of an electric shock. Do not overload the power supply cable. Do not use the power supply cable in order
to carry the tool or to connect and disconnect the plug from the mains socket. Avoid contact of the power supply cable
with heat, oils, sharp tools and moving elements. Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under eff ects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries. Always
use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks, protec-
tive shoes, helmets and hearing protections permits to reduce the risk of serious injuries. Avoid accidental activation of the
tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a fi nger
on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries. Before you turn an
electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating
elements of the tool may lead to serious injuries. Keep your balance. Maintain an appropriate position. It will permit to control
the electric tool in case of unpredicted situations during its operation. Use protective clothes. Do not wear loose clothes or
jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool. Loose clothes, jewellery or
long hair may get caught on moving elements of the tool. Use dust extractors or dust containers, if the tool is equipped with
any. Make sure they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.
Caution when using a power tool.
Before inserting a battery pack make sure that the switch stays in "OFF" position. Inserting a battery pack into a power tool,
when the switch is in "ON" position may cause accidents.
Use only chargers recommended by the manufacturer. Using a charger designed for only one type of battery pack, to charge
other types of battery pack may be a cause of fi re.
Use power tools only with battery pack specifi ed by the manufacturer. Use of other battery pack may be a cause of injuries
or fi re.
When the battery pack is not used, it should be stored away from metal objects, such as paper clips, coins, nails, bolts or
other small metal elements, that may short the terminals. Shorting terminals of a battery may cause burns or fi re.
In adverse conditions, a liquid may escape from a battery; avoid any contact with this liquid. In case of accidental contact
with a liquid, rinse with water. If a liquid gets into your eyes, please seek medical advice. A liquid escaping from a battery
may cause irritations or burns.
Repairs
Have the tool repaired solely by authorised workshops, where original spare parts are used. This will ensure the adequate
safety of operation of the electric tool.
ADDITIONAL SAFETY INSTRUCTIONS
The tool is designed only for grinding, polishing, work with wire brush, carving and cutting. Read all the warnings, in-
structions, illustrations and specifi cations supplied along with this power tool. Failure to observe all instructions presented
below may lead to electric shock, fi re and/or serious injuries.
Do not use any accessories that have not been designed and are not recommended by the manufacturer. The fact that any
accessory may be installed does not mean that it guarantees safe operation.
Maximum rotational speed of accessories must be higher or equal to maximum rotational speed of the tool. Accessories
of smaller rotational speed than the speed of the tool may disintegrate during operation.
Outer diameter and thickness of accessories must stay within the range defi ned for the tool.
Accessories of wrong dimensions may not be properly controlled.
Size of mounting hole of wheels, discs, fl anges and other accessories must fi t the size of tool's spindle. Accessories with
mounting hole not fi lling the size of tool's spindle will start vibrating after the start and this may result in loss of control of the tool.
Shafts of: discs, polishing wheels, cutting discs must be inserted in full into hand grip or tool chuck. If the shaft is not
suffi ciently held down and/or it protrudes too far, the tool inserted may be loosened and ejected at a high speed.
Do not use damaged accessories. Before each use check the condition of such accessories as abrasive wheels for the
O R I G I N A L I N S T R U C T I O N S
15