Black and Decker LST520 Manual De Instrucciones página 6

the battery pack in an air temperature
below +40°F (+4.5°C), or above +105°F
(+40.5°C). This is important and will prevent
serious damage to the battery pack.
2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does
not indicate a problem. To facilitate the
cooling of the battery pack after use,
avoid placing the charger or battery pack
in a warm environment such as in a
metal shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by
plugging in a lamp or other appliance
b. Check to see if receptacle is connected
to a light switch which turns power off
when you turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 65°F -
75°F (18°- 24°C).
d. If charging problems persist, take the
appliance, battery pack and charger
to your local service center.
4. The battery pack should be recharged
when it fails to produce sufficient power on
jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse affect
on the battery pack.
5. Foreign materials of a conductive nature
such as, but not limited to, steel wool,
aluminum foil, or any buildup of metallic
particles should be kept away from
charger cavities. Always unplug the
charger from the power supply when there
is no battery pack in the cavity. Unplug
charger before attempting to clean.
6. Do not freeze or immerse charger in
water or any other liquid.
WARNING:
Shock hazard. Do not
allow any liquid to get inside charger. Never
attempt to open the battery pack for any
reason. If the plastic housing of the battery
pack breaks or cracks, return to a service
center for recycling.
INStAllING ANd ReMoVING
tHe BAtteRY PAcK FRoM
tHe APPlIANce
WARNING:
Make certain the lock-off
button is not engaged to prevent switch
actuation before removing or installing battery.
TO INSTALL BATTERY PACK: Insert battery
(12) into appliance until an audible click is
heard (Figure B). Ensure battery pack is fully
seated and fully latched into position.
TO REMOVE BATTERY PACK: Depress
the battery release button (13) as shown
in Figure c and pull battery pack out of
appliance.
B
c
SAVe tHeSe INStRuctIoNS
ASSeMBlY ANd AdjuStMeNt
WARNING:
MAKE SURE THAT THE APPLIANCE IS
SWITCHED OFF AND THE BATTERY HAS
BEEN REMOVED.
ASSeMBlY toolS ReQuIRed
(Not SuPPlIed):
- Phillips Screwdriver
INStAllING tHe GuARd
WARNING:
FRoM tHe APPlIANce BeFoRe
AtteMPtING to AttAcH tHe GuARd,
edGe GuIde oR HANdle. NeVeR
oPeRAte APPlIANce WItHout
GuARd FIRMlY IN PlAce. tHe GuARd
MuSt AlWAYS Be oN tHe APPlIANce
to PRotect tHe uSeR.
• Remove the screw from the guard.
• Turn the trimmer upside down so that you
are looking down at the spool cap (14).
• Turn the guard (10) upside down and slide
it fully onto the motor housing (15). Make
sure the tabs (16) on the guard engage the
ribs (17) on the motor housing as shown.
• Continue to slide the guard on until you
hear it "snap" into place. The locking tab
(18) should snap into the housing slot (19).
6
12
13
BEFORE ASSEMBLY,
ReMoVe tHe BAtteRY