Murray 204110x52B Manual De Instrucciones página 8

How To Order Replacement Parts
The replacement parts are shown either on the
back pages of this Instruction Book or in a
separate Parts List Book.
Use only manufacturer's authorized or approved
replacement parts. The letter placed on the end
of the part number denotes the type of finish for
the part, C for chrome, Z for zinc, a PA for
purchased assembly. It is important that you
include this when ordering a part. Do not use
attachments or accessories not specifically
recommended for this unit. In order to obtain
proper replacement parts you must supply the
model number of your mower (see nameplate).
Replacement parts, except for the engine,
transmission, transaxle or differential, are
available from the store where the mower was
purchased or a service shop recommended by
the store.
If you are unable to obtain parts or service in the
manner outlined above, then contact:
HAYTER LIMITED,
Service Department,
Spellbrook,
Bishop's Stortford,
Hertfordshire. CM23 4BU.
MURRAY, INC.
International Sales
P.O. Box 268
Brentwood, Tennessee USA 37024
1-800-251-8007
Fax (615) 373-6633 Collect telephone calls will
not be accepted.
Replacement parts for the engine, transaxle, or
transmission, are available from the
manufacturer's authorized service centre found
in the commercial pages of the telephone
directory. Also, see the individual engine or
transmission warranties to order replacement
parts.
When ordering the following information is
required:
(1) The Model Number
(2) Serial Number
(3) Part Number
(4) Quantity
F-050452L
TROUBLE SHOOTING CHART
The Engine will not start.
1. Make sure the fuel tank is filled with clean
petrol. Do not use old petrol.
2. On a cold engine, push the primer button
(optional on some models) five times.
3. Make sure the wire for the spark plug is con-
nected to the spark plug.
4. Adjust the carburettor. See the engine
manufacturer's instructions.
5. There is too much petrol in the engine cylin-
der. Remove and dry the spark plug. Pull the
recoil-start grip several times. Install the
spark plug. Connect the wire to the spark
plug. Start the engine.
6. The engine is difficult to start in heavy or high
grass. Move the mower to a clean dry sur-
face.
7. Make sure the engine stop lever is in the op-
erating position.
8. Make sure the fuel valve is in the ON posi-
tion. See the engine manufacturer's instruc-
tions.
The Engine will not stop.
1. Release the engine stop lever.
2. Check the engine stop cable. Replace the
cable if bent or damaged.
The Engine performance is bad.
1. Check the height of cut settings. Raise the
height of cut if the grass is high.
2. Check the bottom of the blade housing.
Clean the blade housing of grass and other
debris.
3. Check the wire to the spark plug. Make sure
the wire is connected.
4. Clean the engine cooling fins of grass and
other debris.
5. Check the carburettor adjustments. See the
engine manufacturer's instructions.
6. Check the spark plug gap. Set the spark plug
gap at 0.030".
7. Check the amount of oil in the engine. Fill
with oil if necessary.
8. Check the engine air cleaner. See the engine
manufacturer's instructions.
9. The petrol is bad. Drain and clean the fuel
tank. Fill the fuel tank with clean petrol.
Excessive Vibration.
1. Remove the blade. Check the blade and bal-
ance if necessary. See the blade mainte-
nance instructions.
2. Check for a bent or broken blade. A DAM-
AGED BLADE IS DANGEROUS AND MUST
BE REPLACED.
3. Check the blade adapter. REPLACE A BRO-
KEN BLADE ADAPTER.
4. If the vibration continues, take the mower to
an Authorized Service Centre.
8
The grass will not discharge correctly.
1. Clean the bottom of the mower housing.
2. Check for a badly worn blade. Remove and
sharpen the blade. For safety, replace the
blade every two years with a factory replace-
ment blade.
The grass is not cut even.
1. Check the height adjustment at each wheel.
The height adjustment must be the same for
each wheel.
2. Make sure the blade is sharp.
3. Check for a bent or broken blade. A DAM-
AGED BLADE IS DANGEROUS AND MUST
BE REPLACED.
4. Check for a broken blade adapter. REPLACE
A BROKEN BLADE ADAPTER.
GB