Descargar Imprimir esta página

Panasonic DMR-E65 Instrucciones De Funcionamiento página 20

Publicidad

Idiomas disponibles

Idiomas disponibles

Timer recording
Refer to the control reference on page 19.
[RAM] [DVD-R]
You can enter up to 16 programmes up to a month in advance.
(Each daily or weekly programme is counted as one programme.)
Manually programming timer
recordings
1
Press [PROG/CHECK].
TIMER
RECORDING
No. Name
Date
Start
01
ARD
15/ 7 TUE
19:00
New Timer Programme
SELECT
ENTER
RETURN
2
Press [3, 4] to select "New Timer
Programme" and press [ENTER].
3
Press [1] to move through the items
and change the items with [3, 4].
TIMER
RECORDING
Name
Date
1 ARD
15/ 7 TUE
≥Press and hold [3, 4] to alter the Start (Start time) and
Stop (Finish time) in 30-minute increments.
≥You can also set Name (Programme position/TV Station
Name), Date, Start (Start time), and Stop (Finish time) with
the numbered buttons.
≥You can also press [REC MODE] to change the recording
mode.
≥Date
[.
Date:
l
;:
l
Daily timer:
l
;:
a.
Weekly timer: SUN>--->SAT
≥VPS/PDC ( page 19)
ON!)OFF (– – –)
≥Programme Name
Press [2, 1] to select "Programme Name" and press
[ENTER] ( page 40).
4
Press [ENTER].
TIMER
RECORDING
No. Name
Date
Start
01
ARD
15/ 7 TUE
19:00
02
ARD
15/ 7 TUE
22:00
New Timer Programme
Repeat steps 2–4 to programme other recordings.
5
Press [F TIMER].
The unit turns off and "F" lights on the unit's display to
indicate timer recording standby has been activated.
RQT7542
20
20
Remain
1:58 SP
12:56:00 15. 7. TUE
Disc
VPS
Stop
Mode
space
PDC
20:00
SP
OFF
OK
Press ENTER to store
new programme.
Remain
1:58 SP
12:57:00 15. 7. TUE
VPS
Start
Stop
Mode
PDC
22:00
22:30
SP
OFF
Programme Name
Current date up to one month later minus
one day
SUN-SAT>MON-SAT>MON-FRI
Remain
1:58 SP
12:58:00 15. 7. TUE
VPS
Disc
Stop
Mode
space
PDC
Check to make sure
OFF
20:00
SP
OK
22:30
SP
OFF
OK
"OK" is displayed
( page 21).
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.
∫ To release the unit from recording standby
Press [F TIMER].
The unit turns on and "F" goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if "F" is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.
[Note]
≥"F" flashes for about 5 seconds when the unit cannot go to
timer recording standby (e.g., a recordable disc is not in the
disc tray).
≥If the unit is not put in the timer recording standby mode at the
latest 10 minutes before the programmed timer recording
starting time, the "F" flashes on the unit display. In this case,
press [F TIMER] to put the unit in the timer recording standby
mode.
≥When you programme successive timer recordings to start
immediately one after the other, the unit cannot record the part
at the beginning of the later programmes (a few seconds when
recording with DVD-RAM and approximately 30 seconds when
recording with DVD-R).

Publicidad

loading