Milwaukee 9071-20 Manual Del Operador página 5

Attaching and Removing the Tool Hanger
(Cat. No. 9092-20, 9096-20, or as accessory)
1.To attach, remove the two
top gear case screws.
2. Place the ring through
the tool hanger.
3. Position the tool hanger
on the tool over the two
gear case screw holes.
4. Replace the two gear
case screws. Hand tight-
en the screws.
5. To remove, reverse the
procedure.
Attaching and Removing Accessories
(Cat. No. 9071-20, 9075-20
This impact wrench is intended only for use with
sockets designed for impact wrenches and that
have a 1/2" square drive (3/4" square drive for Cat.
No. 9075-20). Other sockets could shatter or break,
causing injury.
1. To attach a socket or other accessory, push the
accessory onto the drive shank until it snaps into
place.
2. To remove the accessory, pull it off the drive shank.
Attaching and Removing Accessories
(Cat. No. 9070-20, 9072-20, 9072-22)
These impact wrenches are intended only for use
with sockets designed for impact wrenches and that
have a 1/2" square drive. Other sockets could shatter
or break, causing injury.
1. To attach a socket or other acces-
sory, align the hole in the acces-
sory with the detent pin on the
drive shank. Hold the detent pin
in while pushing the socket onto
the drive shank. The detent pin
will snap into place in the hole
to secure the socket.
2. To remove the accessory, insert a nail or other thin
object into the hole in the accessory and press
the detent pin in. Pull the accessory off the drive
shank.
Attaching and Removing Accessories
(Cat. No. 9092-20, 9096-20, or other Impact
Wrenches using the Quick Change 1/2" Square
Drive to 7/16" Hex Adapter)
Cat. No. 9092-20 and accessory Cat. No. 48-66-0061
are intended for use with accessories with a 7/16"
Hex Quick Change shank. Cat. No. 9096-20 is in-
tended for use with accessories with a 5/8" Hex Quick
Change shank. Both Hex Quick Change shanks have
a ball-retainer groove. They are not intended for use
with Hex Shank Bit Extensions.
1. To attach an accessory, pull the chuck collar
forward and insert the accessory shank. Release
the collar. It may be necessary to pull the bit out
slightly to engage the holding mechanism.
2. To remove the accessory, pull the chuck collar
forward and remove the accessory. Release the
collar.
Gear
case
screws
)
Detent
Pin
Ball-retainer
groove
OPERATION
To reduce the risk of injury, always
WARNING
unplug tool before attaching or
removing accessories or making adjustments.
Use only specifically recommended accessories.
Others may be hazardous.
To reduce the risk of injury, always wear safety
goggles or glasses with side shields.
Using the Forward/Reverse Switch
(Cat. No. 9072-20, 9072-22, 9092-20, and 9096-20)
This impact wrench is equipped with a forward/re-
verse switch that may be set to forward or reverse
rotation.
1. For forward (clockwise) rotation, push the forward/
reverse switch in the direction shown. Check the
direction of rotation before use.
2. For reverse (counterclockwise) rotation, push
the forward/reverse switch in the direction shown.
Check the direction of rotation before use.
Reverse
To reduce the risk of injury, keep
WARNING
hands and cord away from the bit
and all moving parts.
To reduce the risk of explosion, electric shock
and property damage, always check the work
area for hidden pipes and wires
before drilling.
To reduce the risk of injury, only
grasp tool by handle and red
insulated surfaces. Do not hold
gray gear case when impacting
or drilling.
5
Closed (Locked)
Open (Release)
Forward
Forward/Reverse Switch