Milwaukee 2607-20 Manual Del Operador página 5

Selecting Hammer, Drill or Drive Action
(Cat. No. 2607-20)
1. To use the hammer-drilling mode,
rotate the application selector col-
lar until the hammer symbol
appears in line with the arrow.
Apply pressure to the bit to engage
the hammering mechanism.
NOTE: The number selected on
the torque selector collar has no effect on opera-
tion of the drill in hammer mode.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the drilling only mode,
rotate the application selector col-
lar until the drill symbol
pears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
3. To use the driving screws mode,
rotate the application selector col-
lar until the drive symbol
pears in line with the arrow. Then
rotate the torque selector collar
until the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when prop-
erly adjusted, will slip at a preset torque to prevent
driving the screw too deep into different materials
and to prevent damage to the screw or tool.
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
Cat. No. 2606-20
Clutch
Setting in. lbs
1-5 15-30 Small screws in softwood.
6-10 32-40 Medium screws in softwood or small
screws in hardwood.
11-15 43-50
Large screws in softwoods. Medium
16-17 55-100 screws in hardwood or large screws in
hardwood with pilot hole.
Cat. No. 2607-20
Clutch
Setting in. lbs
1-3 28-30 Small screws in softwood.
4-6 31-33
Medium screws in softwood or small
7-9 34-39 screws in hardwood.
10-13 41-47
Large screws in softwoods. Medium
14-17 49-55 screws in hardwood or large screws in
hardwood with pilot hole.
18 57
NOTE: Because the settings shown in the table are only a
guide, use a piece of scrap material to test the different clutch
settings before driving screws into the workpiece.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
ap-
ap-
Applications
Applications
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete
stop before using the control
switch.
For forward (clockwise)
rotation, push in the control
switch from the right side of
the tool. Check the direc-
tion of rotation before use.
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
To reduce the risk of injury, always
WARNING
hold or brace securely.
Starting, Stopping and Controlling Speed
1. To start the tool, grasp the handles firmly and pull
the trigger.
NOTE: An LED is turned on when the trigger is pulled.
2. To vary the speed, increase or decrease the pres-
sure on the trigger. The further the trigger is pulled,
the greater the speed.
3. To stop the tool, release the trigger. Make sure
the bit comes to a complete stop before laying the
tool down.
APPLICATIONS
To reduce the risk of electric shock,
WARNING
check work area for hidden pipes
and wires before drilling or driving screws.
Drilling
Place the bit on the work surface and apply firm pres-
sure before starting. Too much pressure will slow the
bit and reduce drilling efficiency. Too little pressure
will cause the bit to slide over the work area and dull
the point of the bit.
If the tool begins to stall, reduce pressure slightly to
allow the bit to regain speed. If the bit binds, reverse
the motor to free the bit from the workpiece.
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently to
clear chips from the bit flutes. To reduce the chance of
splintering, back work with a piece of scrap wood. Se-
lect low speeds for plastics with a low melting point.
Drilling in Metal
When drilling in metal, select the
ating mode. Use high speed steel twist drills or hole
saws. Use a center punch to start the hole. Lubricate
drill bits with cutting oil when drilling in iron or steel.
Use a coolant when drilling in nonferrous metals such
as copper, brass or aluminum. Back the material
to prevent binding and distortion on breakthrough.
5
Forward
Lock
Push to
CENTER
drill-only operating mode.
drill-only oper-
Reverse